GM Service Manual Online
For 1990-2009 cars only

Exhaust Manifold Replacement - Right Side 4.3L Engine

Removal Procedure


    Object Number: 664837  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the right exhaust manifold pipe nuts.
  3. Lower the vehicle.

  4. Object Number: 360851  Size: SH
  5. Loosen the air cleaner outlet duct clamp at the mass airflow/intake air temperature (MAF/IAT) sensor.

  6. Object Number: 701705  Size: SH
  7. Remove the positive crankcase ventilation (PCV) hose.

  8. Object Number: 489179  Size: SH
  9. Remove the air cleaner adapter nut.

  10. Object Number: 489176  Size: SH
  11. In order to remove the air cleaner outlet duct, pivot the duct upward until the hinge clip releases from the lip on the throttle body.
  12. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement in Engine Mechanical - 4.3L.

  13. Object Number: 14824  Size: SH
  14. Disconnect the spark plug wires from the spark plugs.
  15. Remove the spark plug wire retainer bolt.
  16. Reposition the wire retainer to the top of the engine.
  17. Remove the spark plugs.

  18. Object Number: 188121  Size: SH
  19. Remove the exhaust manifold and spark plug heat shield bolts.
  20. Remove the exhaust manifold and spark plug heat shields.

  21. Object Number: 328555  Size: SH
  22. Remove and discard the exhaust manifold gaskets.

  23. Object Number: 493851  Size: SH
  24. Remove the exhaust manifold heat shield, if required.
  25. Clean all gasket mating surfaces.

Installation Procedure


    Object Number: 493851  Size: SH
  1. Install the exhaust manifold heat shield to, if required.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the exhaust manifold heat shield bolts.
  4. Tighten
    Tighten the exhaust manifold heat shield bolts to 9 N·m (80 lb in).


    Object Number: 476818  Size: SH

    Important: To assist in installing the exhaust manifold and gasket to the engine, tabs on a NEW exhaust manifold gasket will hold the gasket and bolts in place.

  5. Install NEW exhaust manifold gaskets to the exhaust manifold.
  6. Ensure that the exhaust manifold bolts, and plug wire shields are held in place by the tabs on the exhaust manifold gaskets.

  7. Object Number: 188121  Size: SH
  8. Install the exhaust manifold and plug wire shields.
  9. If reusing the old fasteners, apply threadlock GM P/N United States 12345493, GM P/N Canada 10953488, or equivalent to the threads of the exhaust manifold bolts.
  10. Tighten the exhaust manifold bolts.
  11. Tighten
    Tighten the exhaust manifold bolts to 30 N·m (22 lb ft).


    Object Number: 14824  Size: SH
  12. Install the spark plugs.
  13. Position the spark plug wire retainer to the engine.
  14. Loosely install the spark plug wire retainer bolt.
  15. Connect the spark plug wires to the spark plugs.
  16. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement in Engine Mechanical - 4.3L.
  17. Tighten
    Tighten the spark plug wire retainer bolt to 12 N·m (106 lb in).


    Object Number: 489176  Size: SH
  18. Align the hinge clip with the lip on the throttle body.
  19. In order to install the air cleaner outlet duct, pivot the air cleaner outlet duct downward until the mounting stud is through the hole.


    Object Number: 489179  Size: SH
  20. Install the air cleaner adapter nut.

  21. Object Number: 701705  Size: SH
  22. Install the PCV hose.

  23. Object Number: 360851  Size: SH
  24. Tighten the air cleaner outlet duct clamp at the MAF/IAT sensor.
  25. Raise the vehicle.

  26. Object Number: 664837  Size: SH
  27. Install the right exhaust manifold pipe nuts.
  28. Tighten
    Tighten the exhaust manifold pipe nuts to 50 N·m (37 lb ft).

  29. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 4.8L, 5.3L, and 6.0L Engines


    Object Number: 664837  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the exhaust manifold pipe nuts.
  3. Lower the vehicle.
  4. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement for the 4.8L, 5.3L, and 6.0L engines.
  5. Remove the spark plugs. Refer to Spark Plug Replacement for the 4.8L, 5.3L, and 6.0L engines.

  6. Object Number: 679527  Size: SH
  7. Remove the bolts (1, 2, 3) attaching the exhaust gas recirculation (EGR) valve pipe to the following, if equipped:
  8. • Intake manifold
    • Cylinder head
    • Exhaust manifold
  9. Remove the EGR valve pipe and gaskets, if equipped.
  10. With mild force, pull the EGR valve pipe from the intake manifold.

  11. Remove the O-ring seal from the EGR valve pipe, if equipped.
  12. Discard the gasket and the O-ring seal, if equipped.

  13. Object Number: 741554  Size: SH
  14. Remove the exhaust manifold bolts, manifold, and gasket. Discard the bolts.
  15. Discard the gasket.

  16. Object Number: 492768  Size: SH
  17. Remove the heat shield bolts (1), and shield (2) from the exhaust manifold (1), if necessary.
  18. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection for the 4.8L, 5.3L engines, and 6.0L Unit Repair.

Installation Procedure

  1. Install the exhaust manifold to the cylinder head. Refer to Exhaust Manifold Installation - Right Side .

  2. Object Number: 679527  Size: SH
  3. Apply a light coating of clean engine oil to a NEW O-ring seal and install the seal onto the EGR valve pipe, if equipped.
  4. Install the EGR pipe, if equipped.
  5. Notice: Refer to Fastener Notice in the Preface section.

  6. Install the EGR valve pipe bolts until snug, if equipped.
  7. Tighten

    1. Tighten the EGR valve pipe to intake manifold bolt (1) to 10 N·m (89 lb in).
    2. Tighten the EGR valve pipe to cylinder head bolts (2) to 50 N·m (37 lb ft).
    3. Tighten the EGR valve pipe to exhaust manifold bolts (3) to 30 N·m (22 lb ft).
  8. Install the spark plugs. Refer to Spark Plug Replacement for the 4.8L, 5.3L, and 6.0L engines.
  9. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement for the 4.8L, 5.3L, and 6.0L engines.
  10. Raise the vehicle.

  11. Object Number: 664837  Size: SH
  12. Install the exhaust manifold pipe nuts.
  13. Tighten
    Tighten the exhaust manifold pipe nuts to 50 N·m (37 lb ft).

  14. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 6.6L Engine

Removal Procedure


    Object Number: 660371  Size: SH
  1. Raise the vehicle enough in order to work through the wheelhouse opening. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  3. Remove the front tire and wheel, if necessary. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  4. Remove the exhaust manifold heat shield bolts.
  5. Remove the exhaust manifold heat shield.

  6. Object Number: 777476  Size: SH
  7. Remove the right exhaust pipe to the exhaust manifold bolts (1).

  8. Object Number: 660374  Size: SH
  9. Remove the bolts/nuts from the right exhaust manifold.
  10. Remove the exhaust manifold.
  11. Remove the bolt for the oil level indicator tube bracket in order to remove the exhaust manifold gasket.
  12. Remove and discard the exhaust manifold gasket.
  13. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection in Engine Mechanical - 6.6L Unit Repair.

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 654543  Size: SH
  1. Install the exhaust manifold gasket to the cylinder head.
  2. Install the bolt for the oil level indicator tube bracket.
  3. Tighten
    Tighten the oil level indicator tube bracket bolt to 21 N·m (15 lb ft).

  4. Install the exhaust manifold.
  5. Install the exhaust manifold bolts/nuts.

  6. Object Number: 1872601  Size: SH
  7. Use the sequence shown, properly tighten the exhaust manifold bolts.
  8. Tighten

    1. Tighten the exhaust manifold bolt/nuts a first pass to 34 N·m (25 lb ft).
    2. Tighten the exhaust manifold bolts/nuts a final pass to 34 N·m (25 lb ft).

    Object Number: 660371  Size: SH
  9. Install the exhaust manifold heat shield.
  10. Install the exhaust manifold heat shield bolts.
  11. Tighten
    Tighten the exhaust manifold heat shield bolts to 8 N·m (71 lb in).


    Object Number: 777476  Size: SH
  12. Install the exhaust pipe gasket. Align the tab on the gasket to face outward.
  13. Install the exhaust pipe bolts (1).
  14. Tighten
    Tighten the exhaust pipe to exhaust manifold bolts to 53 N·m (39 lb ft).

  15. Install the wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  16. Install the front tire and wheel, if necessary. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  17. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 8.1L Engine

Removal Procedure


    Object Number: 470704  Size: SH
  1. Remove the wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  2. Remove the oil level indicator. Refer to Oil Level Indicator and Tube Replacement in Engine Mechanical - 8.1L.
  3. Important: Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug or the wire could be damaged.

  4. Remove the spark plug wires from the spark plugs and ignition coils.
  5. Remove the spark plugs. Refer to Spark Plug Replacement in Engine Controls - 8.1L.

  6. Object Number: 635635  Size: SH
  7. Remove the exhaust gas recirculation (EGR) pipe nuts from the exhaust manifold.
  8. Remove the EGR pipe bracket bolt.
  9. Remove and discard the EGR pipe gasket.
  10. Reposition the EGR pipe.
  11. Raise and suitably support the vehicle with safety stands. Refer to Lifting and Jacking the Vehicle in General Information.

  12. Object Number: 470706  Size: SH
  13. Remove the exhaust manifold heat shield bolts and nuts.
  14. Remove the exhaust manifold heat shield.
  15. Lower the vehicle.

  16. Object Number: 470719  Size: SH
  17. Remove the exhaust manifold bolt and nuts.
  18. Remove the exhaust manifold.
  19. Remove and discard the exhaust manifold gasket.
  20. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection in Engine Mechanical - 8.1L Unit Repair.

Installation Procedure


    Object Number: 470719  Size: SH
  1. Install the a NEW exhaust manifold gasket.
  2. Install the exhaust manifold.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the exhaust manifold bolt and nuts.
  5. Tighten

        • Tighten the exhaust manifold bolt to 35 N·m (26 lb ft).
        • Tighten the exhaust manifold nuts to 16 N·m (12 lb ft).
  6. Raise and suitably support the vehicle with safety stands.

  7. Object Number: 470706  Size: SH
  8. install the exhaust manifold heat shield.
  9. Install the exhaust manifold heat shield bolts and nuts.
  10. Tighten
    Tighten the exhaust manifold heat shield bolts/nuts to 25 N·m (18 lb ft).

  11. Lower the vehicle.

  12. Object Number: 635635  Size: SH
  13. Position the EGR pipe.
  14. Install a NEW EGR pipe gasket.
  15. Install the EGR pipe bracket bolt.
  16. Tighten
    Tighten the EGR pipe bracket bolt to 50 N·m (37 lb ft).

  17. Install the EGR pipe nuts to the exhaust manifold.
  18. Tighten
    Tighten the EGR pipe nuts to 30 N·m (22 lb ft).

  19. Install the spark plugs. Refer to Spark Plug Replacement in Engine Controls - 8.1L.

  20. Object Number: 470704  Size: SH

    Important: Fully install the spark plug wires by pushing on the exposed end of the spark plug boot. Do not push the spark plug wire on to the spark plug by using the metal heat shield.

  21. Install the spark plug wires to the spark plugs and ignition coils.
  22. Install the oil level indicator. Refer to Oil Level Indicator and Tube Replacement in Engine Mechanical - 8.1L.
  23. Install the wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.