Parking Brake Rear Cable Replacement - Right Side without/RPO NYS

1. Release the park brake.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



3. Relieve the tension on the cable by loosening the nut at the equalizer.
4. Disconnect the cable from the equalizer.



5. Remove the bolt from the rear axle clip.
6. Remove the cable from the differential clip.



7. Remove the cable from the mounting bracket by depressing the locking tabs.



8. Remove the cable from the left and right side cable guides, 15 series utilities.
9. Remove the cable from the track bar clips.



10. Remove the cable from the lever, all except 15 series utilities.
11. Remove the cable from the backing plate by depressing the locking tabs.
12. Remove the cable from the retaining bracket.
13. Remove the cable.



14. Remove the cable from the lever, 15 series utilities.
15. Remove the cable from the backing plate by depressing the locking tabs.
16. Remove the cable from the retaining bracket.
17. Remove the cable.

1. Install the cable taking care to correctly route the cable through the guides and the body mounts.
2. Install the cable to the backing plate by pressing the cable into place until locking tabs snap into place, 15 series utilities.
3. Attach the cable to the lever.



4. Install the cable taking care to correctly route the cable through the guides and the body mounts.
5. Install the cable to the backing plate by pressing the cable into place until locking tabs snap into place, all except 15 series utilities.
6. Attach the cable to the lever.



7. Install the cable to the track bar and secure with the clips. Verify that the clips are installed between the locators on the track bar, 15 series utilities.
8. Install the cable to the right and left side guides.



9. Install the cable to the mounting bracket until the locking tabs snap into place.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

10. Bolt the cable to the differential clips.

Tighten
Tighten the bolt to 25 N·m (18 lb ft).

Important: After installing the cable to the rear axle holding clip, verify that clip is securely retaining the cable. If not, crimp the clip by hand taking care not to pinch or kink the cable.

11. Install the cable to the differential clip.
12. Connect the cable to the equalizer.



13. Tighten the nut to the intermediate cable at the equalizer.

Tighten
Tighten the nut to 3.5 N·m (31 lb in).

14. Remove the safety stands.
15. Lower the vehicle.
16. Adjust the park brake cable. Refer to Park Brake Adjustment .

Parking Brake Rear Cable Replacement - Right Side with RPO NYS

1. Release the park brake.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



3. Remove the park brake cable from the equalizer by pulling down on the intermediate cable and release the cable from the equalizer bar.



4. Remove the cable from the mounting bracket by depressing the locking tabs.



5. Remove the park brake cable from the differential clip.

Remove the bolt retaining the park brake cable from the rear axle clip.




6. Remove the rear brake cable mounting bracket bolt.



7. Remove the brake cable from the lever.



8. Remove the cable (2) from the rear brake cable mounting bracket (3) by depressing the locking tabs (1) on the brake cable.



9. Remove the brake cable from the guides and the body mounts.

1. Install the new brake cable (2) into the rear brake cable mounting bracket (3) by pushing the cable into place until the locking tabs (1) snap into place.



2. Install the park brake cable to the lever.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the rear park brake cable bracket bolt.

Tighten
Tighten the rear park brake cable bracket bolt to 61 N·m (45 lb ft).




4. Install the park brake cable to the differential clip.
5. Install the park brake cable bolt to the rear axle clip.

Tighten
Tighten the park brake cable bolt to 25 N·m (18 lb ft).




6. Install the park brake cable taking care to correctly route the cable though the guides and the body mounts.
7. Install the park brake cable into the mounting bracket until the locking tabs snap into place.



8. Install the park brake cable to the equalizer bar.
9. Remove the safety stands.
10. Lower the vehicle.