Lower Control Arm Replacement RWD

Tools Required

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
3. For vehicles with rack and pinion steering, remove the front coil spring. Refer to Front Coil Springs Replacement .
4. For vehicles with recirculating ball steering, remove the torsion bar. Refer to Torsion Bar Replacement .
5. Remove the front stabilizer shaft link. Refer to Stabilizer Shaft Replacement .
6. Remove the shock absorber. Refer to Shock Absorber Replacement .



7. Remove the lower control arm nuts and the 15-series washers.
8. Remove the lower control arm 15-series bolts.



9. Remove the lower control arm nuts and the 25/35-series washers.
10. Remove the lower control arm 25/35-series bolts.



11. Remove the lower ball joint retaining nut.



12. Disconnect the lower ball joint stud from the steering knuckle using J 43631 and J 45851 .
13. Remove the lower control arm.

1. Install the lower control arm.
2. Connect the ball joint stud to the steering knuckle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




3. Install the lower ball joint retaining nut.

Tighten
Tighten the nut to 100 N·m (74 lb ft).

4. For vehicles with rack and pinion steering, install the front coil spring. Refer to Front Coil Springs Replacement .



5. Install the lower control arm 15-series bolts.
6. Install the lower control arm nuts and the 15-series washers.

Tighten
Tighten the nuts to 145 N·m (107 lb ft).




7. Install the lower control arm 25/35-series bolts.
8. Install the lower control arm nuts and the 25/35-series washers.

Tighten
Tighten the nuts to 150 N·m (110 lb ft).

9. For vehicles with recirculating ball steering, install the torsion bar. Refer to Torsion Bar Replacement .
10. Install the front stabilizer shaft link. Refer to Stabilizer Shaft Replacement .
11. Install the shock absorber. Refer to Shock Absorber Replacement .
12. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
13. Remove the safety stands.
14. Lower the vehicle.
15. Verify the wheel alignment. Refer to Wheel Alignment Measurement in Wheel Alignment.

Lower Control Arm Replacement 4WD

Tools Required

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
3. Remove the stabilizer shaft links from the lower control arm. Refer to Stabilizer Shaft Replacement .
4. Remove the shock absorber lower nut and the bolt. Refer to Shock Absorber Replacement .
5. Remove the torsion bars. Refer to Torsion Bar Replacement .
6. Remove the wheel drive shaft. Refer to Wheel Drive Shaft Replacement in Wheel Drive Shafts.



7. Remove the lower ball joint retaining nut.



8. Disconnect the lower ball joint stud from the steering knuckle using J 43631 and J 45851 .



9. Remove the lower control arm nuts and the 15-series washers.
10. Remove the lower control arm bolts.



11. Remove the lower control arm nuts and the 25/35-series washers.
12. Remove the lower control arm bolts.
13. Remove the lower control arm.

1. Install the lower control arm.



2. Install the lower control arm 15-series bolts.



3. Install the lower control arm 25/35-series bolts.



4. Install the washers with the shoulder facing the arm.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the lower control arm retaining nuts.

Tighten
Tighten the nuts to 150 N·m (110 lb ft).

6. Install the wheel drive shaft. Refer to Wheel Drive Shaft Replacement in Wheel Drive Shafts.



7. Connect lower ball joint stud to the steering knuckle.
8. Install the retaining nut to the lower ball joint stud.

Tighten
Tighten the nut to 100 N·m (74 lb ft).

9. Install the torsion bars. Refer to Torsion Bar Replacement .
10. Install the shock absorber lower nut and bolt. Refer to Shock Absorber Replacement .
11. Install the stabilizer shaft links to the lower control arm. Refer to Stabilizer Shaft Replacement .
12. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
13. Remove the safety stands.
14. Lower the vehicle.
15. Align the vehicle. Refer to Wheel Alignment Measurement in Wheel Alignment.