Circuit Description
The DRL 10 A fuse in the engine wiring harness junction block supplies battery positive voltage to the daytime running lamp (DRL) relay switch contacts. The IGNE 10 A fuse in the engine wiring harness junction block supplies ignition positive voltage to the DRL relay coil. When the BCM energizes the DRL relay in daylight conditions, the current flow is to both DRL lamps and to ground G100.
The body control module (BCM) monitors the ambient light sensor signal circuit of the ambient light sensor in order to determine if the daytime running lights (DRL) or the auto headlights (AHL) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage between 1.7-4.7 volts (light state) the DRL will be commanded ON. When the BCM senses the ambient light sensor voltage between 0.2 1.0 volts (dark state) the AHL will be commanded ON.
Conditions for Running the DTC
| • | The system voltage must be between 9.0 and 16.0 volts. |
| • | The ignition switch must be in the RUN position. |
| • | The park brake must be released. |
| • | The headlamp switch must be in the AUTO position. |
Conditions for Setting the DTC
| • | When the ambient light sensor input voltage is greater than 4.78 volts (the ambient light sensor signal is shorted to the battery). |
| • | The above conditions must be met for 0.5 seconds. |
Action Taken When the DTC Sets
The AHL will remain ON in any ambient light state.
Conditions for Clearing the DTC
| • | This DTC will clear immediately after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
| • | A clear codes message is sent by the scan tool. |
Diagnostic Aids
Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Tests for the proper operation of the ambient light sensor signal circuit in the low voltage range.
-
Tests for the proper operation of the ambient light sensor signal circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.
-
Tests for a short to voltage in the 5 volt reference circuit.
-
After replacement of the BCM you must calibrate the new module for proper operation.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting System Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the Ambient Light Sensor parameter is within the specified range? | 0.2-4.7 V | Go to Diagnostic Aids | Go to Step 3 |
Does the scan tool indicate that the Ambient Light Sensor parameter is less than the specified value? | 0.2 V | Go to Step 4 | Go to Step 9 | |
Does the scan tool indicate that the Ambient Light Sensor parameter is greater than the specified value? | 4.7 V | Go to Step 5 | Go to Step 7 | |
Does the voltage measure less than the specified value? | 5.25 V | Go to Step 10 | Go to Step 6 | |
6 | Test the 5 volt reference circuit of the ambient light sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 |
7 | Test the 5 volt reference circuit of the ambient light sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 8 |
8 | Test the ambient light sensor signal circuit of the ambient light sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 |
9 | Test the ambient light sensor signal circuit of the ambient light sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 |
10 | Inspect for poor connections at the harness connector of the ambient light sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 |
11 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 |
12 | Replace the ambient light sensor. Refer to Ambient Light Sensor Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- |
|
Important: Perform the setup procedure for the body control module. Replace the body control module. Refer to Body Control Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 14 | -- | |
14 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
