GM Service Manual Online
For 1990-2009 cars only

Exhaust Pipe Replacement - Left Side 6.6L (LB7) Engine

Removal Procedure


    Object Number: 707396  Size: SH
  1. Remove the turbocharger exhaust pipe. Refer to Turbocharger Exhaust Pipe Replacement .
  2. The turbocharger exhaust pipe does not need to be removed from the vehicle in order to remove the left exhaust pipe. Position the turbocharger exhaust pipe out of the way.

  3. Remove the exhaust heat shield nuts (2) heat shield (3) from the dash panel.

  4. Object Number: 668426  Size: SH
  5. Remove left exhaust pipe heat shield bolts.
  6. Position the heat shield to the side in order to access the exhaust manifold to exhaust pipe bolts.
  7. Do not remove the heat shield at this time.


    Object Number: 785649  Size: SH
  8. Remove the exhaust manifold to exhaust pipe bolts (2).
  9. Remove and discard the gasket.
  10. Lower the vehicle.
  11. Remove the exhaust pipe heat shield. The shield will remove from the top of the engine.
  12. Remove the exhaust pipe bolts (1) from the turbocharger.
  13. Remove the exhaust pipe with the gasket.
  14. Clean the exhaust pipe.
  15. Clean the exhaust pipe mating surfaces.
  16. Inspect the exhaust pipe for dents and cracks.
  17. Replace the exhaust pipe if any damage is found.

Installation Procedure


    Object Number: 785649  Size: SH
  1. Install the exhaust pipe with a NEW gasket to the turbocharger. Align the tab on the gasket at the turbocharger to face inward.
  2. To aid in installation temporarily install an exhaust pipe to exhaust manifold bolt.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the exhaust pipe to turbocharger bolts (1).
  4. Tighten
    Tighten the bolts to 53 N·m (39 lb ft).

  5. Install the exhaust pipe heat shield but do not install the bolts.
  6. Raise the vehicle.
  7. Install the exhaust pipe with a NEW gasket to the exhaust manifold. Align the tabs on the gasket to face outward.
  8. Install the exhaust pipe to exhaust manifold bolts (2).
  9. Tighten
    Tighten the bolts to 53 N·m (39 lb ft).


    Object Number: 668426  Size: SH
  10. Install the exhaust pipe heat shield bolts.
  11. Tighten
    Tighten the bolts to 8 N·m (71 lb in).


    Object Number: 707396  Size: SH
  12. Install the left side exhaust heat shield (3) at the dash panel.
  13. Install the heat shield nuts (2).
  14. Tighten
    Tighten the nuts to 9 N·m (80 lb in).

  15. Install the turbocharger exhaust pipe. Refer to Turbocharger Exhaust Pipe Replacement .

Exhaust Pipe Replacement - Left Side 6.6L (LLY) Engine

Removal Procedure


    Object Number: 707396  Size: SH
  1. Remove the right wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  2. Remove the exhaust heat shield nuts (2) and heat shield (3) from the dash panel.

  3. Object Number: 1334829  Size: SH
  4. Remove the left exhaust pipe heat shield bolts.
  5. Remove the heat shield.

  6. Object Number: 721427  Size: SH
  7. Remove the exhaust pipe bolts in the proper sequence.

  8. Object Number: 1334832  Size: SH
  9. Remove the exhaust pipe and gaskets.
  10. Discard the gaskets.

Installation Procedure


    Object Number: 1334832  Size: SH
  1. Position the exhaust pipe with a NEW gasket to the turbocharger. Align the tab on the gasket at the turbocharger to face inward.
  2. Loosely install the bolts.
  3. Position the exhaust pipe with a NEW gasket to the exhaust manifold. Align the tab on the gasket to face outward.
  4. Loosely install the bolts.
  5. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 721436  Size: SH
  6. Tighten the exhaust pipe bolts in the sequence shown.
  7. Tighten
    Tighten the bolts to 53 N·m (39 lb ft).


    Object Number: 1334829  Size: SH
  8. Install the exhaust pipe heat shield bolts.
  9. Tighten
    Tighten the bolts to 8 N·m (71 lb in).


    Object Number: 707396  Size: SH
  10. Install the left side exhaust heat shield (3) at the dash panel.
  11. Install the heat shield nuts (2).
  12. Tighten
    Tighten the nuts to 9 N·m (80 lb in).

  13. Install the right wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.