GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The auxiliary power outlet (APO) switch controls the operation of the hybrid control module (HCM) APO state manager. The APO state manager commands one of 3 states from the starter generator control module (SGCM) (APO Off, APO Normal, APO Continuous). The APO switch is a momentary button, its output signal an input to an HCM analogue channel. Five volts are supplied to the switch; the returned voltage is measured relative to HCM signal ground to determine the switch state. A resistor network in the switch circuitry ensures that shorted high and low states can be diagnosed successfully. There are 2 valid voltage ranges of the return signal, one representing switch open, the other representing switch closed. If the voltage is lower than a threshold, a short low is indicated. Similarly, if the voltage is greater than the short high threshold, a short 'high' is indicated.

Conditions for Running the DTC

    • The ignition is ON.
    • The APO switch is requested ON.

Conditions for Setting the DTC

    •  If voltage is lower than a calibrated value, a short low is indicated.
    •  If the voltage is greater than a calibrated value the short high is indicated.
    • This DTC is run every 100 milliseconds.

Action Taken When the DTC Sets

    • The control module stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
    • The driver information center (DIC), if equipped, may display a message.

Conditions for Clearing the DTC

    • The Conditions for Setting the DTC are no longer present.
    • A history DTC will clear after 40 malfunction-free ignition cycles.
    • The HCM receives the clear code command from the scan tool.

Step

Action

Yes

No

Schematic Reference: Cigar Lighter/Power Outlet Schematics

Connector End View Reference: Power Outlet Connector End Views

1

Did you perform the Diagnostic System Check - Power Outlets?

Go to Step 2

Go to Diagnostic System Check - Power Outlets

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Place the auxiliary power outlet (APO) switch in the normal or continuous mode.
  4. With a scan tool, observe the Auxiliary Power Outlets Switch parameter in the data list for the hybrid control module (HCM).

Does the scan tool display ON?

Go to Step 3

Go to Step 4

3

  1. Place the APO switch in the OFF mode.
  2. With the scan tool, observe the APO Switch Status parameter.

Does the APO Switch Status parameter display OFF?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the APO switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the APO Switch Status parameter.

Does the scan tool display OFF?

Go to Step 7

Go to Step 5

5

Test the signal circuit of the APO switch for a open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 6

6

Inspect for poor connections at the harness connector of the HCM . Refer to Connector Repairs and Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 8

7

Inspect for poor connections at the harness connector of the APO switch. Refer to Connector Repairs and Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 9

8

Important: Always perform the setup procedure for the HCM.

  1. Replace the HCM. Refer to Powertrain Control Interface Module Replacement in Engine Electrical.
  2. Perform the setup procedure for the HCM.

Did you complete the replacement?

Go to Step 10

--

9

Replace the APO switch. Refer to Accessory Switch Replacement in Instrument Panel, Gages, and Console.

Did you complete the replacement?

Go to Step 10

--

10

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC reset?

Go to Step 2

System OK