GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Important: Clean the fuel and evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the lines in order to avoid possible system contamination.


    Object Number: 1528274  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .
  2. Disconnect the chassis fuel feed line at the engine fuel line (1). Refer to Metal Collar Quick Connect Fitting Service .
  3. Disconnect the EVAP line (3). Refer to Plastic Collar Quick Connect Fitting Service .
  4. Cap the engine fuel line (1), and EVAP line (3) in order to avoid possible system contamination.
  5. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  6. Object Number: 1238747  Size: SH
  7. Remove the fuel pipe bracket nut.
  8. Remove the fuel pipe bracket from the bellhousing stud.
  9. Remove the heated oxygen sensor (HO2S) sensor connector from the bracket.

  10. Object Number: 1549620  Size: SH
  11. Remove the fuel line clip from the bracket on the transmission.
  12. If equipped with 4-wheel drive (4WD), remove the fuel line clip from the bracket on the transfer case.
  13. Remove the clip from the bracket on the frame.
  14. Remove the transfer case harness from the clip bracket.

  15. Object Number: 924296  Size: SH

    Important: The area around the electro-hydraulic control unit (EHCU) MUST be free from loose dirt to prevent contamination of disassembled anti-lock brake (ABS) components.

  16. Thoroughly wash all contaminants from around the EHCU.
  17. Disconnect the chassis electrical harness connectors from the electronic brake control module (EBCM).

  18. Object Number: 379478  Size: SH

    Important: Make sure the brake lines are tagged and kept in order for proper reassembly.

  19. Disconnect the brake lines from the brake pressure modulator valve (BPMV).
  20. Remove the bolts (4) attaching the EHCU bracket to the frame (5).
  21. Remove the EHCU (1).

  22. Object Number: 1238591  Size: SH
  23. If equipped with 4WD, remove the torsion bar bracket. Refer to Torsion Bar Replacement .
  24. Disconnect the fuel and EVAP lines at the fuel tank. Refer to Plastic Collar Quick Connect Fitting Service .
  25. Cap the fuel and EVAP lines at the fuel tank in order to avoid possible system contamination.

  26. Object Number: 1238831  Size: SH
  27. Remove the fuel and EVAP bundle clip nuts.
  28. Remove the fuel and EVAP bundle.

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1238831  Size: SH
  1. Install the fuel and EVAP bundle.
  2. Install the fuel and EVAP bundle clip nuts.
  3. Tighten
    Tighten the nuts to 12 N·m (106 lb in).


    Object Number: 1238591  Size: SH
  4. Remove the caps from the fuel and EVAP lines at the fuel tank.
  5. Connect the fuel and EVAP quick connect fittings. Refer to Plastic Collar Quick Connect Fitting Service .
  6. If equipped with 4WD, install the torsion bar bracket. Refer to Torsion Bar Replacement .

  7. Object Number: 379478  Size: SH
  8. Install the EHCU (1).
  9. Install the bolts (4) attaching the EHCU bracket to the frame (5).
  10. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 924296  Size: SH
  11. Connect the brake lines to the BPMV.
  12. Tighten
    Tighten the fittings to 25 N·m (18 lb ft).

  13. Connect the chassis electrical harness connectors to the EBCM.
  14. Install the transfer case harness to the clip bracket.
  15. Install the clip to the bracket on the frame.

  16. Object Number: 1549620  Size: SH
  17. If equipped with 4WD, install the fuel line clip to the bracket on the transfer case.
  18. Install the fuel line clips to the brackets on the transmission.
  19. Install the HO2S sensor connector to the bracket.

  20. Object Number: 1238747  Size: SH
  21. Install the fuel pipe bracket to the bellhousing stud.
  22. Install the fuel pipe bracket nut.
  23. Tighten
    Tighten the nut to 10 N·m (89 lb in).

  24. Lower the vehicle.

  25. Object Number: 1528274  Size: SH
  26. Remove the caps from the engine fuel line (1) and EVAP line (3).
  27. Connect the EVAP line (3). Refer to Plastic Collar Quick Connect Fitting Service .
  28. Connect the chassis fuel feed line at the engine fuel line (1). Refer to Plastic Collar Quick Connect Fitting Service .
  29. Install the fuel fill cap.
  30. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  31. Use the following procedure in order to inspect for leaks:
  32. 23.1. Turn the ignition ON, with the engine OFF, for 2 seconds.
    23.2. Turn the ignition OFF for 10 seconds.
    23.3. Turn the ignition ON, with the engine OFF.
    23.4. Inspect for fuel leaks.