VEHICLE APPLICATIONS: B,F AND Y CARS C,K,R,V,S,T - TRUCKS G,M, VANS
New Product Information for all 1989 THM 700-R4 transmissions. Refer to each section of this bulletin for specific product change information.
DATE OF PRODUCTION CHANGE: (Figure 1) ------------------------- Beginning with 1989 Start of Production, all 1989 THM 700-R4 transmissions were built with the product changes explained in this bulletin.
Changes listed in this bulletin as "Service Manual Update" will note changes made since publication of the 1989 Service Manual and should be noted in your 1989 Service Manual accordingly.
Other changes described in this bulletin are included in your 1989 THM 700-R4 Service Manual sections. Be certain to familiarize yourself with these changes to properly service the 1989 THM 700-R4 transmission.
CHANGE TO ASSEMBLY COMPONENTS: (Figure 2) ----------------------------- A new Input Clutch Assembly with 3-4 clutch boost springs (600) introduced for all 1989 THM 700-R4 models. (This Input Clutch Assembly and 3-4 clutch boost springs were first used in the 1988 model year on the YDM, YMM, YWM and YZM models; reference bulletin 88-7700-101. The boost springs aid the release of the 3-4 clutch on downshifts.
When servicing any 1989 THM 700-R4 transmission, the 3-4 clutch boost springs must be used. Improper shift timing can occur if these springs are not installed. When overhauling the 3-4 clutch assembly, the 3-4 clutch boost springs should be inserted in place after installation of the 3-4 clutch plates, just prior to installing the 3-4 clutch backing plate and snap ring.
Part No. Description --------- ----------- 8667424 Spring Asm, Boost 3-4 Clutch (600) - (5 required)
This information is included in your 1989 Service Manual Unit Repair Section. Information that is new for 1989 is noted by an asterisk in the Unit Repair Table of Contents.
This information (Figures 3 and 4) has been updated since publication of the 1989 Service Manual. Use this information to update your 1989 THM 700-R4 Automatic Transmission Diagnosis Section.
CHANGE TO ASSEMBLY COMPONENTS: (Figures 5-7) ----------------------------- Beginning with the 1989 model year, the FMM model THM 700-R4 transmission uses a Type 18 Solenoid Assembly and Wiring Harness (refer to Figure 5). The Type 18 Solenoid Assembly and Wiring Harness was introduced late in the 1988 model year and replaced most Type 15 Solenoid Assembly production (reference Bulletin 88-7700-105. The FMM model is the last Type 15 Solenoid Assembly model to change to Type 18 usage.
New for 1989 is a Type 19 Solenoid Assembly and Wiring Harness (refer to Figures 6). The Type 19 Solenoid Assembly were introduced at 1989 start of Production.
Part No. Description -------- ----------- 10478100 Type 18 Solenoid Assembly - Complete
10478101 Type 19 Solenoid Assembly - Complete
This information (Figures 5-6) has been updated since publication of the 1989 Service Manual. Use this information to update your 1989 THM 700-R4 Automatic Transmission Diagnosis Section.
General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.