GM Service Manual Online
For 1990-2009 cars only

Engine Coolant Fan Shroud Replacement Upper

Removal Procedure

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable (dual batteries only).

  2. Object Number: 72746  Size: SH
  3. For the 5.0L, remove the upper fan shroud bolts and the upper fan shroud.

  4. Object Number: 72745  Size: SH
  5. For the 5.7L, remove the upper fan shroud bolts and the upper fan shroud.

  6. Object Number: 72744  Size: SH
  7. For the 7.4L, remove the upper fan shroud bolts and the upper fan shroud.

  8. Object Number: 72741  Size: SH
  9. For the 6.5L (Diesel), remove the upper fan shroud bolts and the upper fan shroud.
  10. Inspect the upper fan shroud for signs of damage. If necessary, replace the upper fan shroud.

Installation Procedure


    Object Number: 72746  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. For the 5.0L, install the upper fan shroud and upper fan shroud bolts.
  2. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72745  Size: SH
  3. For the 5.7L, install the upper fan shroud and upper fan shroud bolts.
  4. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72744  Size: SH
  5. For the 7.4L, install the upper fan shroud and upper fan shroud bolts.
  6. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72741  Size: SH
  7. For the 6.5L (Diesel), install the upper fan shroud and upper fan shroud bolts.
  8. Tighten
    Tighten the bolts to 9 N·m (71 lb in).

  9. Connect the negative battery cable (dual batteries only).

Engine Coolant Fan Shroud Replacement Lower

Removal Procedure

  1. Remove the upper fan shroud. Refer to Fan Shroud Replacement .
  2. Raise the vehicle.
  3. Remove the front differential carrier shield (if equipped). Refer to Front Drive Axle Description and Operation in Front Drive Axle.

  4. Object Number: 72746  Size: SH
  5. For the 5.0L, remove the lower fan shroud bolts and the lower fan shroud.

  6. Object Number: 72745  Size: SH
  7. For the 5.7L, remove the lower fan shroud bolts and the lower fan shroud.

  8. Object Number: 72744  Size: SH
  9. For the 7.4L, remove the lower fan shroud bolts and the lower fan shroud.

  10. Object Number: 72741  Size: SH
  11. For the 6.5L (Diesel), remove the lower fan shroud bolts and the lower fan shroud.
  12. Inspect the lower fan shroud for signs of damage. If necessary, replace the lower fan shroud.

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 72746  Size: SH
  1. For the 5.0L, install the lower fan shroud and the lower fan shroud bolts.
  2. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72745  Size: SH
  3. For the 5.7L, install the lower fan shroud and the lower fan shroud bolts.
  4. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72744  Size: SH
  5. For the 7.4L, install the lower fan shroud and the lower fan shroud bolts.
  6. Tighten
    Tighten the bolts to 9 N·m (71 lb in).


    Object Number: 72741  Size: SH
  7. For the 6.5L (Diesel), install the lower fan shroud and the lower fan shroud bolts.
  8. Tighten
    Tighten the bolts to 9 N·m (71 lb in).

  9. Install the front differential carrier shield (if equipped). Refer to Front Drive Axle Description and Operation in Front Drive Axle.
  10. Lower the vehicle.
  11. Install the upper fan shroud. Refer to Fan Shroud Replacement .