GM Service Manual Online
For 1990-2009 cars only

Object Number: 190383  Size: SF
KS/Ckp - Comp Loc Figure
Ignition Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The control module contains a removable knock sensor (KS) module which receives the knock sensor input. The knock sensor signal input is filtered by this module before it is input to the controls module. Spark knock is continuously monitored during engine operation. If knock occurs for longer than a calibrated time, this diagnostic trouble code (DTC) will set.

Conditions for Running the DTC

    • DTC P0327 is not active
    • The engine run time is 120 seconds or more
    • The system voltage is between 10-17.1 volts

Conditions for Setting the DTC

The VCM detects engine knock for more than 5 seconds

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles.
    • The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records.

Conditions for Clearing the MIL or DTC

    • The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed.
    • A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle.
    • Use a scan tool in order to clear the DTCs.

Diagnostic Aids

Check for the following conditions:

    • A damaged or improperly installed Knock Sensor module. Check for the following items:
       - Bent pins
       - Deformed terminals
       - Knock Sensor module not completely seated
    • Improper knock sensor torque specification. Refer to

Notice: Replacement components must be the correct part number for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque, which may affect the operation of the component. Use the correct torque specification when installing components in order to avoid damage.

in Cautions and Notices. Torque the knock sensor to 19 N·m (14 lb ft).
    • A misrouted wiring harness

Refer to Symptoms .

Review the Fail Records vehicle mileage since the diagnostic test last failed to determine how often the conditions occur that caused the DTC to set . This may assist in diagnosing the condition.

An intermittent may be caused by any of the following conditions:

    • A poor connection
    • Rubbed through wire insulation
    • A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step ensures that the condition is present.

  2. This step checks for an improperly installed Knock Sensor module.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used.

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Important: If you can hear the engine knock, repair the engine mechanical problem before proceeding with this diagnostic.

  1. Operate the engine within the conditions specified in Conditions for Running the DTC.
  2. Monitor the Specific DTC info for the DTC P0325 until the test runs with the scan tool.

Does the scan tool indicate the DTC P0325 Failed This Ignition?

--

Go to Step 4

Go to Step 3

3

  1. Turn ON the ignition leaving the engine OFF.
  2. Review the scan tool Failure Records data for DTC P0325.
  3. Record the scan tool Failure Records data for DTC P0325.
  4. Operate the vehicle within the Failure Records conditions.
  5. Monitor the Specific DTC info for DTC P0325 until the test runs with the scan tool.

Does the scan tool indicate DTC P0325 test Failed This Ignition?

--

Go to Step 4

Go to Diagnostic Aids

4

Check the KS signal circuit wiring for incorrect routing near the secondary wires. Repair as necessary.

Did you find a problem?

--

Go to Step 9

Go to Step 5

5

Check the Knock Sensor module for incorrect installation. Repair as necessary. Refer to VCM Replacement/Programming .

Did you find a problem?

--

Go to Step 9

Go to Step 6

6

Replace the Knock Sensor module. Refer to VCM Replacement/Programming .

Is the action complete?

--

Go to Step 7

--

7

  1. Using the scan tool, clear the DTCs.
  2. Start the engine.
  3. Allow the engine to idle until the engine reaches normal operating temperature.
  4. Select DTC and the Specific DTC function.
  5. Enter the DTC number which was set.
  6. Operate the vehicle, with the Conditions for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

--

Go to Step 10

Go to Step 8

8

  1. Replace the VCM.
  2. Program the new VCM. Refer to VCM Replacement/Programming .
  3. Perform the Passlock Reprogramming Procedure.
  4. Perform the CKP System Variation Learn Procedure. Refer to Crankshaft Position System Variation Learn .

Is the action complete?

--

Go to Step 9

--

9

  1. Using the scan tool, clear the DTCs.
  2. Start the engine.
  3. Allow the engine to idle until the engine reaches normal operating temperature.
  4. Select DTC and the Specific DTC function.
  5. Enter the DTC number which was set.
  6. Operate the vehicle, with the Conditions for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

--

Go to Step 10

Go to Step 2

10

Does the scan tool display any additional undiagnosed DTCs?

--

Go to the applicable DTC table

System OK