Shock Absorber Replacement RWD

Notice: The front shock absorbers of the vehicle are multifunctional. In addition to contributing to a smooth ride they also provide the only stop to the front suspension when fully extended. Therefore, when servicing the shock absorber, service replacement shock absorbers must be equivalent to original shock absorbers in both extended length and strength. Use of shocks not complying to original equipment or strength could result in suspension over-travel or shock breakage. Suspension over-travel may result in suspension component breakage.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Disconnect the electrical connector using the following procedure if equipped with selectable ride.



3. Grasp the connector lock tabs (1, 2). Rotate the connector tabs counter clockwise until the connector is unlocked.
4. Disengage the connector from the tennon by firmly pulling the connector up.
5. Hold the tennon end with a wrench while removing the nut.
6. Remove the nut.



7. Remove the upper insulator (1). Do not discard the plastic pilot ring (2).



8. Remove the shock absorber mounting bolts at the lower control arm.
9. Remove the shock absorber through the lower control arm from below.

1. Support the lower control arm with a suitable jack in order to align the tennon with the mounting hole if equipped with selectable ride.
2. Install the shock absorber through the lower control arm from below. Insert the tennon through the mounting hole in the upper spring pocket.
3. Align the shock absorber with the mounting holes in the lower control arm.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the shock absorber mounting bolts to the lower control arm.

Tighten
Tighten the bolts to 25 N·m (18 lb ft).





Important: The upper insulators are substantially larger that the lower insulators. The upper insulator (1) must be installed above the shock mounting bracket on the frame. The plastic pilot ring (2) will assist the alignment of the isolators.

5. Install the upper insulator to the shock absorber.
6. Install the nut to the tennon end. Do not tighten the nut.
7. Remove the safety stands.
8. Lower the vehicle.
9. Hold the tennon end with a wrench while torquing the nut.

Tighten
Tighten the nut to 20 N·m (15 lb ft).

10. Connect the electrical connector using the following procedure if equipped with selectable ride.

10.1.

Verify that the connector is unlocked.

10.2.

Align the connector so that the tabs (1) are perpendicular to the wrench flats on the tennon end.

10.3.

Engage the connector to the tennon by firmly pushing the connector down.





10.4.

Grasp the connector lock tabs (1, 2). Rotate the connector counter clockwise.




11. The connector is locked into place when you hear an audible snap and the tabs (1, 2) are aligned.

Shock Absorber Replacement 4WD

Notice: The front shock absorbers of the vehicle are multifunctional. In addition to contributing to a smooth ride they also provide the only stop to the front suspension when fully extended. Therefore, when servicing the shock absorber, service replacement shock absorbers must be equivalent to original shock absorbers in both extended length and strength. Use of shocks not complying to original equipment or strength could result in suspension over-travel or shock breakage. Suspension over-travel may result in suspension component breakage.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Disconnect the electrical connector if equipped with selectable ride.



3. Grasp the connector lock tabs (1, 2). Rotate the connector tabs counter clockwise until the connector is unlocked.
4. Disengage the connector from the tennon by firmly pulling the connector up.
5. Hold the tennon end with a wrench while removing the nut.
6. Remove the nut.



7. Remove the upper insulator (1). Do not discard the plastic pilot ring (2).



8. Remove the shock absorber mounting bolt at the lower control arm (15 Series).
9. The lower shock mounting bushing is serviceable by driving the bushing out with the appropriate tool.



10. Remove the shock absorber mounting bolt (2) at the lower control arm (25 Series).
11. Remove the shock absorber.

1. Install the shock absorber. Insert the stem through the hole in the shock bracket on the frame.
2. Align the shock absorber with the mounting holes in the lower control arm (15 Series).



3. Align the shock absorber with the mounting holes in the lower control arm (25 Series).
4. Install the shock absorber through the bolt (2) to the lower control arm.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the shock absorber through the bolt nut (3).

Tighten
Tighten the nut to 80 N·m (59 lb ft).





Important: The upper insulators are substantially larger that the lower insulators. The upper insulator (1) must be installed above the shock mounting bracket on the frame. The plastic pilot ring (2) will assist the alignment of the isolators.

6. Install the upper insulator to the shock absorber.
7. Install the nut to the tennon end. Do not tighten the nut.
8. Remove the safety stands.
9. Lower the vehicle.
10. Hold the tennon end with a wrench while torquing the nut.

Tighten
Tighten the nut to 20 N·m (15 lb ft).

11. Connect the electrical connector using the following procedure if equipped with selectable ride.

11.1.

Verify that the connector is unlocked.

11.2.

Align the connector so that the tabs (1) are perpendicular to the wrench flats on the tennon end.

11.3.

Engage the connector to the tennon by firmly pushing the connector down.





11.4.

Grasp the connector lock tabs (1, 2). Rotate the connector counter clockwise.




12. The connector is locked into place when you hear an audible snap and the tabs (1, 2) are aligned.