GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2001 🢒 GMC MD Steel Tilt (F Model) 🢒 Bulletins 🢒 High Shift Effort On Manual Transmission (Replace Gearshift Control (Change Lever) Assembly and Shift Cable)

High Shift Effort On Manual Transmission (Replace Gearshift Control (Change Lever) Assembly and Shift Cable)

Subject:High Shift Effort on Manual Transmission (Replace Gearshift Control (Change Lever) Assembly and Shift Cable)

Models:1997-2001 Chevrolet and GMC F Model (T-Series) Medium Duty Tilt Cab
2000-2001 Chevrolet and GMC WT 5500 Series Medium Duty Tilt Cab
With MLD6Q Isuzu Manual Transmission (RPO M54)


Condition

Some customers may comment on high transmission shift effort while driving.

Correction

Replace the gearshift control (change lever) assembly and shift cable using the following procedure. The gearshift control (change lever) assembly is not serviced as an assembly. Individual parts must be obtained and assembled. Assemble a new gearshift control (change lever) using the parts listed below. Use the old gearshift control (change lever) assembly as an aid to assemble parts.

    Important: Apply the parking brake and block all of the wheels on the vehicle prior to starting this procedure.


    Object Number: 203426 Size: SH
  1. Place the transmission in the neutral position.
  2. Remove the shift control knob from the shift control lever.

    3. Object Number: 203427 Size: SH
  3. Remove the four screws securing the shift boot to the gearshift control (change lever) bracket.

    4. Object Number: 203428 Size: SH
  4. Remove the two nuts, the washers, and the clips securing the shift and select cables to the gearshift control (change lever) assembly.
  5. Remove the two nuts and washers securing the gearshift control (change lever) assembly to the panel.
  6. Remove the shift cable from the panel.

    7. Object Number: 204762 Size: SH
  7. Remove the nut, the washer, and the clip securing the shift cable to the transmission control lever.

    8. Object Number: 206550 Size: SH
  8. Remove the bolts and nuts securing the shift cable to the rear frame rail bracket.

    9. Object Number: 206549 Size: SH
  9. Remove the bolts and nuts securing the shift cable to the front frame rail brackets. Note the routing of the shift cable.
  10. Install the bolts and nuts securing the new shift cable to the frame rail brackets.

    11. Tighten
    Tighten the bolts and nuts to 22 N·m (16 lb ft).

  11. Install the nut, the washer, and the clip securing the new shift cable to the transmission control lever.

    12. Tighten
    Tighten the nut to 45 N·m (33 lb ft).

  12. Install the new shift cable through the panel.
  13. Install the two nuts and washers securing the new gearshift control (change lever) assembly to the panel.

    14. Tighten
    Tighten the nuts to 22 N·m (16 lb ft).

  14. Install the two nuts, the washers, and the clips securing the shift and select cables to the gearshift control (change lever) assembly.

    15. Tighten
    Tighten the nuts to 45 N·m (33 lb ft).

  15. Install the four screws securing the shift boot to the new gearshift control (change lever) bracket.
  16. Install the shift control knob to the shift control lever.
  17. Adjust the shift cable using the procedure and table listed below.

Shift Cable Adjustment
  1. Remove the nut and washer securing the shift control cable from the transmission control lever.
  2. Ensure that the transmission shift lever is in the mechanical neutral position.
  3. Turn the adjustment nut at the end of the shift cable in order to obtain the proper rear side of bracket to control lever distance. See the table below.
  4. Install the nut and washer securing the shift cable to the transmission control lever.

    5. Tighten
    Tighten the nuts to 45 N·m (33 lb ft).

  5. Start the engine and verify proper shift operation.

Model

Engine

Adjustment Distance

2000-2001 WT 5500

6HK1-TC

280 mm (11.02 in)

1997-2001 T 6500/7500

6HE1-TC (1997) or 6HK1-TC (1998-2001)

301 mm (11.85 in)

1997-2001 T 8500

6HE1-TC (1997) or 6HK1-TC (1998-2001)

351 mm (13.82 in)

Parts Information

Part Number

Description

Qty

97500221

Bracket, M/Trans Select Lever

1

97500222

Lever, M/Trans Control

1

97719258

Seat, M/Trans Control Lever Ball

1

97719259

Bushing, M/Trans Control Front Shaft

1

97719260

Washer, M/Trans Gear Shift Control Lever Bracket

1

97500223

Lever, M/Trans Control (Select Relay Lever)

1

94252671

Bushing, M/Trans Shaft Lever

2

94054639

Washer, Trans Control, Lever

1

94000085

Ring, Snap

1

94009471

Nut

2

97719261

Spring, Shaft Select Lever Return

1

94312733

Washer

4

97727434

(WT 5500)

Cable, Shift

1

97500375

(T 6500/7500)

Cable, Shift

1

97500376

(T 8500)

Cable, Shift

1

Parts are expected to be available 4-13-2001 from GMSPO.

Warranty Information

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

K2950

Replace Gearshift Control (change lever) Assembly and Shift Cable

1.2 hrs

This is a unique labor operation number for use only with this bulletin. This number will not be published in the Labor Time Guide.