Tools Required

J 21366 Converter Holding Strap

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable.
2. Raise the vehicle.
3. Drain the transmission fluid. Refer to Automatic Transmission Fluid/Filter Changing .
4. Remove the shift cable from the transmission shift lever. Refer to Shift Cable Replacement .
5. Disconnect the electrical connectors (1,2) from each other.
6. Remove the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement or Three-Piece Propeller Shaft Replacement .
7. Support the transmission with a transmission jack.



8. Remove the rear transmission mount.



9. Remove the oil level indicator tube from the transmission. Refer to Transmission Fluid Filler Tube and Seal Replacement .



10. Remove the transmission vent hose from the transmission. Refer to Transmission Vent Hose Replacement .
11. Disconnect the transmission cooler lines. Refer to Oil Cooler Hose/Pipe Replacement .



12. Remove the converter housing cover from the transmission.



13. Mark the flywheel and the torque converter for installation alignment.

Remove the bolts that connect the flywheel to the torque converter.

Important: Support the engine with a jack or a hoist before disconnecting the transmission from the engine.

14. Remove the bolts that secure the engine to the transmission.
15. Slide the transmission straight back from the locating pins and install the J 21366 in order to prevent the converter from falling out of the bell housing.
16. Remove the transmission from the vehicle.

1. Install the transmission to the engine by using the following procedure:

•	The torque converter must be seated properly and the J 21366 must be in place.

•	Support the transmission with a transmission jack.

•	Raise the transmission into place. Remove the J 21366 .

•	Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter.

Important: The torque converter must be flush onto the flywheel and rotate freely by hand.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolts that secure the transmission to the engine.

Tighten
Tighten the bolts and the studs to 44 N·m (33 lb ft).

3. Install the bolts that secure the flywheel to the torque converter.

Tighten to finger tight to insure proper converter seating.

Tighten
Tighten the bolts to 44 N·m (33 lb ft).




4. Install the converter housing cover by hooking the cover under the lip of the engine oil pan.
5. Install the bolts for the converter housing cover.

Tighten
Tighten the cover bolts to 33 N·m (24 lb ft).

6. Connect the transmission cooler lines. Refer to Oil Cooler Hose/Pipe Replacement .



7. Connect the electrical connectors (1,2) to each other.



8. Install the oil level indicator tube. Refer to Transmission Fluid Filler Tube and Seal Replacement .



9. Install the transmission mount.

Tighten
Tighten the mount to the transmission bolts to 44 N·m (33 lb ft).

10. Install the crossmember.

Tighten
Tighten the mount to the crossmember nut to 44 N·m (33 lb ft).

11. Remove the transmission jack.
12. Install the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement or Three-Piece Propeller Shaft Replacement .
13. Install the shift cable. Refer to Shift Cable Replacement .
14. Lower the vehicle.
15. Check the transmission fluid level. Refer to Fluid Capacity Specifications .
16. Connect the negative battery cable.