Circuit Description
The Fuel Level sensor is an important input to the VCM for the Enhanced Evaporative System Diagnostic. The VCM needs the fuel level information in order to know the volume of fuel in the tank. The fuel level affects the rate of change in the air pressure in the EVAP system. Several of the Enhanced Evaporative System Diagnostic sub-test are dependent upon the correct fuel level information. The diagnostic will not run when the tank is more than 85 % or less than 15 % full. (This sensor signal disables the misfire when the fuel levels are less than 15 %).
Conditions for Running the DTC
The VCM has confirmed that the fuel tank is between 15 % and 85 % full.
Conditions for Setting the DTC
The VCM does not detect a decrease in fuel level over a distance of 200 miles(320 km).
Action Taken When the DTC Sets
| • | The control module stores the DTC in history after the first failure but will not illuminate the malfunction indicator lamp (MIL). |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores the failure information in the scan tools Freeze Frame/Failure Records. |
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Check for the following conditions:
| • | A poor connection or damaged harness-- Inspect VCM harness connectors for the following: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Poor wire to terminal connections |
| • | Intermittent test-- monitor a scan tool or digital voltmeter connected between the related circuits while moving the connectors and harnesses. If the failure is induced, the voltage reading will change. This will help locate a circuit problem. |
Test Description
Number(s) below refer to the step number(s) on the diagnostic table.
-
This step determines if there is a wiring problem.
-
This step determines if the Fuel Level sensor signal and ground circuits are OK.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 |
Important: : Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||||||||
|
Important: : If DTCs P0462 and P0463 are also set, diagnose these codes first.
Is the Fuel Level voltage near the specified value? | 5V | |||||||||
Is the Fuel Level sensor voltage near the specified value? | 0V | |||||||||
4 | Repair the open or short to ground in the Fuel Level signal circuit. Refer to Wiring Repairs in Wirirng Systems. Is the action complete? | -- | ||||||||
5 | Check the Fuel Level Sender for the following:
Was a problem found? | -- | ||||||||
6 | Check the Fuel Level sensor signal and ground circuits for an open. Refer to Wiring Repairs in Wiring Systems. Was a problem found? | -- | ||||||||
7 | Repair as necessary. Is the action complete? | -- | -- | |||||||
8 | Replace the Fuel Level Sender. Refer to Fuel Sender Assembly Replacement . Is the action complete? | -- | -- | |||||||
9 |
Was a problem found? | -- | ||||||||
10 |
Is the action complete? | -- | -- | |||||||
11 |
Does the scan tool indicate the diagnostic Passed? | -- | ||||||||
12 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to applicable DTC table | System OK |
