GM Service Manual Online
For 1990-2009 cars only

Disassembly Procedure

Tools Required

    • J 33163 Valve Tray Set
    • J 43773 Valve Spring Compressor

    Notice: Refer to Transmission Control Valve Body Overhaul Notice in the Preface section.


    Object Number: 1581013  Size: SH
  1. Position the control valve on the work table so that the main valve body is facing up.
  2. Remove two bolts (3) retaining the reverse signal pipe.
  3. Important: 

       • Bolt (2) is slightly longer than the other bolts (1).
       • The transmission fluid pressure (TFP) switch is retained by five bolts (1) and by bolt (2).

  4. Remove five bolts (1), and one bolt (2), retaining the TFP switch to the main valve body.

  5. Object Number: 1580997  Size: SH
  6. Remove the reverse signal pipe (2) from the main valve body (3).
  7. Remove the TFP switch (1) from the main valve body (3).

  8. Object Number: 1633324  Size: SH
  9. Remove the 2 bolts (1) retaining the modulated main pressure solenoid valve body (2).
  10. Remove the modulated main pressure solenoid valve body assembly (2) and six speed tube.
  11. Remove the six speed tube from the modulated main pressure solenoid valve body.
  12. Remove the modulated main pressure solenoid retainer (5) from the bottom of the valve body (2).
  13. Remove the modulated main pressure (MAIN MOD) solenoid (6).
  14. Remove the 2 O-rings (3 and 4) from the MAIN MOD solenoid (6).

  15. Object Number: 1581001  Size: SH

    Important: The torque converter clutch (TCC) pressure control solenoid (PCS) retaining bracket (2) must not be modified. Note that the angle between the 2 bracket surfaces is less than 90 degrees. Replace the bracket if the angle is 90 degrees or more.

  16. Remove the bolt (1) that retains the TCC PCS retaining bracket (2) to main valve body.
  17. Remove the TCC PCS retaining bracket (2).
  18. Remove the TCC PCS (7), valve (4), and spring (3).
  19. Remove the O-rings (5 and 6) from the TCC PCS (7).

  20. Object Number: 1331377  Size: SH
  21. Remove the shift solenoid 1 (SS1) retainer (1).
  22. Remove the SS1.
  23. Remove the O-rings (2 and 3) from SS1 (4).

  24. Object Number: 1331380  Size: SH
  25. Remove shift solenoid 3 (SS3) retainer (1).
  26. Remove SS3 (4).
  27. Remove the O-rings (2 and 3) from the SS3 (4).

  28. Object Number: 1331541  Size: SH
  29. Remove the 3 bolts (1) that retain the PCS retaining bracket (2) to the main valve body (3).

  30. Object Number: 1331385  Size: SH
  31. Remove the PCS retaining bracket (1), 2 accumulator springs (2), and 2 accumulator plugs (3).
  32. Remove the pressure control solenoid 1 (PCS1) (15), valve (13), spring (12), valve (11), and spring (10).
  33. Remove the pressure control solenoid 2 (PCS2) (9), valve (7), valve (6), and spring (5).
  34. Remove the O-ring (14) from PCS1 (15).
  35. Remove the O-ring (8) from PCS2 (9).

  36. Object Number: 1331386  Size: SH
  37. Position the control valve module on the work table so that shift valve body (1) is facing up.
  38. Remove the SS1 retainer (2).
  39. Remove the SS1 (5).
  40. Remove the O-rings (3 and 4) from the SS1 (5).

  41. Object Number: 1633330  Size: SH
  42. Remove eleven bolts (1) retaining the shift valve body and the main valve body together.
  43. Position the control valve module on the work table so that the main valve body is facing up. Reinstall four bolts (1) so that the bolts are partially threaded into the shift valve body and protrude from the main valve body.
  44. Position the control valve module on edge so that the top and bottom are vertical.
  45. Gently tap the bolts until the module separates.

  46. Object Number: 1331397  Size: SH
  47. Position the control valve assembly on the work table so that shift valve body (1) is facing up.
  48. Separate shift valve body assembly (1), separator plate (2), and main valve body assembly (4).

Disassembly of Shift Valve Body


    Object Number: 795162  Size: SH
  1. Using J 43773  (2) , compress the shift valve 1 spring until retaining clip (1) is loose. Remove retaining clip (1).

  2. Object Number: 795163  Size: SH
  3. Remove the spring (2) and shift valve 1 (1).

  4. Object Number: 795164  Size: SH
  5. Using J 43773  (2), compress the shift valve 3 spring until the retaining clip (1) is loose. Remove retaining clip (1).

  6. Object Number: 795166  Size: SH
  7. Remove plug (3), spring (2), and shift valve 3 (1).

  8. Object Number: 795169  Size: SH
  9. Using J 43773  (2), compress the shift valve 2 spring until the retaining clip (1) is loose. Remove the retaining clip (1).

  10. Object Number: 795170  Size: SH
  11. Remove plug (3), spring (2), and shift valve 2 (1).

  12. Object Number: 795171  Size: SH
  13. Using J 43773  (2), compress the control main valve spring until retaining clip (1) is loose. Remove retaining clip (1).

  14. Object Number: 795173  Size: SH
  15. Remove spring (2) and control main valve (1).

  16. Object Number: 1581008  Size: SH
  17. Remove solenoid screen (1).

Disassembly of Main Valve Body

Tools Required

    • J 33163 Valve Tray Set
    •  J 43773 Valve Spring Compressor

    Object Number: 795154  Size: SH
  1. Using J 43773  (2), compress the control relief spring until the retaining clip (1) is loose. Remove the retaining clip (1).

  2. Object Number: 795156  Size: SH
  3. Remove the spring (2) and the control relief valve (1).

  4. Object Number: 795159  Size: SH
  5. Using J 43773 , compress the exhaust backfill spring until the retaining clip (1) is loose. Remove the retaining clip (1).

  6. Object Number: 795161  Size: SH
  7. Remove the spring (2) and the backfill exhaust valve (1).