Removal Procedure
- Open the hood.
Caution: Before servicing any electrical component, the ignition and start switch must be in the OFF or LOCK position and all electrical loads
must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury
and/or damage to the vehicle or its components.
- Disconnect
the battery negative cable from the battery. Refer to
Battery Cable
in Engine Electrical.
- Drain the cooling system. Refer to
Cooling System Draining and Filling
in
Engine Cooling.
- Remove the engine electrical wiring harness and lay to the side.
- Disconnect the engine ground straps. Refer to
Engine Ground Strap Replacement
in Engine Electrical.
- Remove the air conditioning compressor from the mounting bracket.
Refer to Refrigerant Recovery and Recharging
in HVAC.
- Remove the air conditioning mounting bracket from the engine block
head.
- Remove the generator from the mounting bracket. Refer to
Generator Replacement
in Engine Electrical.
- Remove the generator mounting bracket from the engine block. Refer
to
Generator Replacement
in Engine Electrical.
- Remove the upper intake manifold from the lower intake manifold.
Refer to
Intake Manifold Replacement
.
- Remove the lower intake manifold from the engine block. Refer
to
Intake Manifold Replacement
.
- Remove the valve rocker arm covers from the cylinder head. Refer
to
Valve Rocker Arm Cover Replacement
.
- Remove the valve rocker arm from the cylinder head. Refer to
Valve Rocker Arm and Push Rod Replacement
.
- Remove the pushrod from the engine block. Refer to
Valve Rocker Arm and Push Rod Replacement
.
- Remove the spark plugs from the cylinder heads. Refer to
Spark Plug Replacement
in Engine Electrical.
- Remove the exhaust manifolds from the cylinder head. Refer to
Exhaust Manifold Replacement
.
- Remove cylinder head bolts
from the engine block.
- Remove the cylinder heads and gasket from the engine block.
- Clean and inspect the sealing surfaces on the cylinder heads.
Refer to Cylinder Head Clean and Inspect
.
Installation Procedure
Important: Do not use sealer on the composition gaskets, and make sure that the
punch code (7.4L) on the cylinder head gasket is facing up.
- Install the cylinder head
gasket to the engine block.
- Install the cylinder head to the engine block.
Important: Make sure that the threads on the cylinder head bolts are clean as well
as the threaded holes in the engine block.
- Coat the threads of the cylinder head bolts with sealing compound
GM P/N 12346004.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the cylinder
head bolts to the cylinder head and tighten finger tight.
Tighten
• | Tighten the first sequence to 40 N·m (30 lb ft). |
• | Tighten the second sequence to 80 N·m (59 lb ft). |
• | Tighten the final sequence to 125 N·m (92 lb ft). |
- Install the push rod into the engine block. Refer to
Valve Rocker Arm and Push Rod Replacement
.
- Install the valve rocker arm to the cylinder head. Refer to
Valve Rocker Arm and Push Rod Replacement
.
- Install the valve rocker arm covers to the cylinder head. Refer
to
Valve Rocker Arm Cover Replacement
.
- Install the exhaust manifolds to the cylinder heads. Refer to
Exhaust Manifold Replacement
.
- Install the spark plugs to the cylinder head. Refer to
Spark Plug Replacement
in Engine Electrical.
- Install the lower intake manifold to the cylinder head. Refer
to
Intake Manifold Replacement
.
- Install the upper intake manifold to the lower intake manifold.
Refer to
Intake Manifold Replacement
.
- Install the engine ground straps to the engine block. Refer to
Engine Ground Strap Replacement
in Engine Electrical.
- Install the generator mounting bracket to the engine block. Refer
to
Engine Ground Strap Replacement
in Engine Electrical.
- Install the generator to the mounting bracket. Refer to
Generator Replacement
in Engine Electrical.
- Install the air conditioning mounting bracket to the cylinder
head.
- Install the air conditioning compressor to the mounting bracket.
Refer to Refrigerant Recovery and Recharging
in HVAC.
- Install the engine electrical wiring harness.
- Fill the cooling system. Refer to
Cooling System Draining and Filling
in
Engine Cooling.
- Connect the battery negative cable to the battery. Refer to
Battery Cable
in Engine Electrical.
- Close the hood.