Wheelhouse Panel Replacement Left

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the battery cables on diesel models.
2. Remove the battery. Refer to Battery Replacement in Engine Electrical.
3. Remove the battery tray on diesel models. Refer to Battery Tray Replacement in Engine Electrical.
4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the left front tire and wheel assembly.



6. Remove the fender from the wheelhouse bolts (3).



7. Remove the 2 bolts (4, 5) holding the wheelhouse to the cowl mounting brackets (6, 7).
8. Remove the 3 wheelhouse to radiator support bolts.
9. Remove the wheelhouse panel from the vehicle.
10. Tilt the panel out of the vehicle.

1. Tilt the panel into the vehicle.

Install the wheelhouse panel to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the 3 wheelhouse-to-radiator support bolts and the nuts.

Tighten
Tighten the wheelhouse-to-radiator support bolts to 25 N·m (18 lb ft).




3. Install the 2 wheelhouse-to-cowl mounting bracket bolts (4, 5).

Tighten
Tighten the wheelhouse-to-cowl bolts to 25 N·m (18 lb ft).




4. Install the fender-to-wheelhouse bolts (3) and the nuts (2).

Tighten
Tighten the fender-to-wheelhouse bolts to 25 N·m (18 lb ft).

5. Install the left front tire and wheel assembly.
6. Lower the vehicle.
7. Install the battery on diesel models.
8. Install the battery tray on diesel models.

Tighten
Tighten the tray bolts to 25 N·m (18 lb ft).

9. Connect the battery cables on diesel models.
10. Close the hood.

Wheelhouse Panel Replacement Right

1. Raise the hood.

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

2. Disconnect the battery cables.
3. Remove the battery. Refer to Battery Replacement in Engine Electrical.
4. Remove the battery tray. Refer to Battery Tray Replacement in Engine Electrical.
5. Remove the heater hoses from the clip on the wheelhouse.
6. Remove the air cleaner hose bracket.
7. Remove the air conditioning evaporator tube from the clip.
8. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Remove the right front tire and wheel assembly.



10. Remove the fender-to-wheelhouse bolts (3).



11. Remove the two bolts (5, 4) holding the wheelhouse to the cowl mounting brackets (6, 7).
12. Remove the three wheelhouse to the radiator support bolts.
13. Remove the wheelhouse panel from the vehicle.
14. Tilt the panel out of the vehicle.

1. Tilt the panel into the vehicle.

Install the wheelhouse panel to the vehicle.





Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the three wheelhouse to radiator support bolts (4) and the nuts (5).

Tighten
Tighten the wheelhouse to radiator support bolts to 25 N·m (18 lb ft).




3. Install the two wheelhouse-to-cowl mounting bracket bolts.

Tighten
Tighten the wheelhouse to the cowl bolts to 25 N·m (18 lb ft).

4. Install the fender to the wheelhouse bolts and the wheelhouse nuts.

Tighten
Tighten the fender to the wheelhouse bolts to 25 N·m (18 lb ft).

5. Install the right front wheel.
6. Lower the vehicle.
7. Install the air conditioning evaporator tube into the clip.
8. Install the air cleaner hose bracket to the wheelhouse.
9. Install the heater hoses into the clip.
10. Install the battery tray.
11. Install the battery.
12. Connect the battery cables.