GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1998 🢒 GMC Suburban - 2WD 🢒 DTC 🢒 DTC P1106 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage

Object Number: 190358 Size: MF
Engine Controls Components
Engine Sensors (L29)
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The manifold absolute pressure (MAP) sensor is a pressure sensor. The control module supplies the MAP sensor a reference voltage, signal, and ground circuits. When manifold vacuum is low, the MAP sensor signal voltage rises to a value near the reference voltage, and the MAP sensor signal voltage decreases when the manifold vacuum increases. The control module monitors the MAP sensor signal circuit voltage in order to calculate the vacuum within the intake manifold.

Certain vehicle models will also use the MAP sensor in order to calculate the barometric pressure (BARO) when the ignition switch is turned ON and the engine is NOT cranked. This BARO reading may also be updated whenever the engine is operated at wide open throttle (WOT).

This DTC is designed to detect intermittent high voltage signals on the MAP sensor circuit.

Conditions for Running the DTC
    • No active TP sensor DTCs
    • The throttle position is 0.4 percent or less with engine speed less than 1200 RPM, or
    • The throttle position is 20 percent or less with engine speed greater than 1200 RPM

Conditions for Setting the DTC

The MAP voltage is greater than 4.4 volts for a calibrated number of seconds.

Action Taken When the DTC Sets

The VCM turns the MIL ON when this DTC is reported and 1 failure has occurred. The VCM substitutes a calculated value for the MAP sensor value so that acceptable performance is maintained.

Conditions for Clearing the MIL/DTC
    • A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles.
    • A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant temperature exceeds 70°C (160°F) during the same ignition cycle.
    • Use the scan tool Clear Information function.

Diagnostic Aids

With the ignition ON and the engine OFF, the manifold pressure is equal to atmospheric pressure with the signal voltage high. The VCM uses this information as an indication of the vehicle's altitude. Comparison of this reading with a known good vehicle using the same sensor is a good way to check the accuracy of a suspect sensor. Readings should be within 0.4 volts. This DTC could set if the sensor ground circuit is intermittently open or the MAP sensor signal circuit is intermittently shorted to voltage. If the high MAP voltage reading is present, additional sensor circuit voltage codes could be set. Refer to any non-intermittent DTCs that are set.

An intermittent may be caused by a poor connection, rubbed through wire insulation, or a broken wire inside the insulation.

Thoroughly check any circuitry that is suspected of causing the intermittent complaint for the following conditions:

    • Backed out terminals
    • Improper mating
    • Broken locks
    • Improperly formed or damaged terminals
    • Poor terminal to wire connections
    • Physical damage to the wiring harness
    • Corrosion
    • Moisture in the connector

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table.

  1. If the MAP sensor voltage is greater than 4.6 volts then the condition is present.

    2.

  2. If any other non-intermittent DTCs are set go there first.

    3.

  3. The engine must be running in order to observe the MAP sensor signal voltage activity.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used.

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. If the engine idle is unstable, incorrect, or if the manifold vacuum at idle is less than the first specified value, correct the condition before using this table. Refer to Symptoms .
  2. Install the scan tool.
  3. Start the engine.
  4. Display the MAP sensor voltage.

Does the scan tool display a MAP sensor voltage greater than the second specified value?

15 in Hg

4.6 V

Go to Step 3

Go to Step 4

3

Are any non-intermittent DTCs set?

--

Go to the applicable DTC table

Go to Step 4

4
  1. Disconnect the MAP sensor harness connector.
  2. Inspect the MAP sensor harness connector and terminals.

Did you find a problem?

--

Go to Step 7

Go to Step 5

5
  1. Disconnect the VCM C2 and C3 connectors.
  2. Inspect the terminals and connectors.

Did you find a problem?

--

Go to Step 7

Go to Step 6

6

  1. Reconnect the VCM and MAP sensor harness connectors.
  2. Start the engine.
  3. Check for an open or short to voltage in the MAP sensor signal circuit or MAP sensor ground circuit while moving the harness in various locations.
  4. Display the MAP sensor voltage while moving the harness.

Did the voltage fluctuate more than the specified value?

0.5 V

Go to Step 7

Go to Diagnostic Aids

7

Repair the circuit as necessary. Refer to Wiring Repairs .

Is the action complete?

--

Go to Step 8

--

8
  1. Using the scan tool, clear the DTCs.
  2. Start the engine.
  3. Allow the engine to idle until the engine reaches normal operating temperature.
  4. Select DTC and the Specific DTC function.
  5. Enter the DTC number which was set.
  6. Operate the vehicle, with the Conditions for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

--

Go to Step 9

Go to Step 2

9

Does the scan tool display any additional undiagnosed DTCs?

--

Go to the applicable DTC table

System OK