GM Service Manual Online
For 1990-2009 cars only

Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle Column Shift


    Object Number: 389651  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Attach the steering column support assembly (2) to the steering column jacket assembly (1) with the 4 TORX® head screws (1).
  2. Tighten
    Tighten the 4 TORX® screws to 17 N·m (13 lb ft).


    Object Number: 361735  Size: SH
  3. Install the steering shaft (1).
  4. Install the adapter and bearing assembly (2).
  5. Install the steering column seal (3).

  6. Object Number: 361734  Size: SH
  7. Install the linear shift assembly (1).
  8. Install the 3 flat head 6-lobed socket tapping screws (2).
  9. Tighten
    Tighten the screws to 10 N·m (89 lb in).


    Object Number: 361733  Size: SH
  10. Install the automatic transmission shift lock control.
  11. Put the column in the NEUTRAL position.

  12. Object Number: 324912  Size: SH
  13. Adjust the automatic transmission shift lock control using the following steps:
  14. 9.1. Pull the tab (1) out on the block side (2) of the automatic transmission shift lock control.
    9.2. Press on the adjuster block (2) to compress the internal adjuster spring to disengage the adjuster teeth. Slide the adjuster block as far away from the solenoid as possible.
    9.3. Lock in place by pushing the tab (1) back in.
  15. Inspect the automatic transmission shift lock control using the following steps:
  16. 10.1. The automatic transmission shift lock control must lock the gear shift lever when it is put into the PARK position.
    10.2. When the column is installed in the vehicle you will not be able to shift the gear shift lever out of the PARK position without pressing on the brake pedal. The solenoid will be energized.
    10.3. Readjust if needed.
  17. Install the turn signal and multifunction switch assembly only. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .
  18. Install the electronic lock module assembly. Refer to Electronic Column Lock Module - Assemble - Off Vehicle .

Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle Floor Shift


    Object Number: 389651  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Attach the steering column support assembly (2) to the steering column jacket assembly (1) with the 4 TORX® head screws (1).
  2. Tighten
    Tighten the 4 TORX® screws to 17 N·m (13 lb ft).


    Object Number: 361735  Size: SH
  3. Install the steering shaft (1).
  4. Install the adapter and bearing assembly (2).
  5. Install the steering column seal (3).
  6. Install the turn signal and multifunction switch assembly. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .
  7. Install the electronic lock module assembly. Refer to Electronic Column Lock Module - Assemble - Off Vehicle .