GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1996 🢒 GMC Suburban - 4WD 🢒 Engine 🢒 Engine Controls - 6.5L 🢒 DTC P0567 Cruise Control Resume Switch Circuit

Object Number: 29564 Size: LF
Handling ESD Sensitive Parts Notice
Engine Controls Components
Cruise Control and 4-Wheel Drive
OBD II Symbol Description Notice

Circuit Description

The cruise Resume/Accel switch is an input to the fuel control portion of the PCM. These inputs allow the PCM to control and hold a requested speed. Cruise Resume/Accel switch sends ignition voltage to the PCM when the switch is switch is closed (ON). This is a type D DTC.

Conditions for Setting the DTC
    • Cruise switch OFF.
    • Ignition voltage on Resume switch signal circuit.

or

    • Cruise switch ON.
    • Resume switch ON for longer than 25.5 seconds.

Action Taken When the DTC Sets
    • Will not turn on the MIL.
    • The PCM will disallow all cruise inputs.
    • TCC shift schedules may be affected.

Conditions for Clearing the MIL/DTC
    • A History DTC will clear when forty consecutive warm-up cycles that the diagnostic does not fail (coolant temperature has risen 5°C (40°F) from start up coolant temperature and engine coolant temperature exceeds 71°C (160°F) that same ignition cycle.
    • Use of a Scan tool

Diagnostic Aids

Check for a resume/accel switch stuck in the engage position or the signal circuit is shorted to voltage.

Test Description

Number(s) below refer to the Step number(s) on the Diagnostic Table.

  1. This Step determines if the signal circuit is shorted to voltage.

    2.

  2. This Step determines if the PCM or switch is at fault.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing DTCs use the scan tool Capture Info to record freeze frame and failure records for reference, as data will be lost when Clear Info function is used.

Was the On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2
  1. Scan tool connected.
  2. Ignition ON, engine OFF.
  3. Cruise switch OFF.

Does scan tool display Resume Switch ON?

--

Go to Step 3

Go to Step 4

3
  1. Ignition ON.
  2. Disconnect the PCM brown 32 way connector.
  3. Probe the Resume switch signal circuit at the PCM harness with a test light connected to chassis ground.

Is the test light ON?

--

Go to Step 5

Go to Step 7

4

DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If additional DTCs were stored refer to the applicable DTC table(s) first.

Are additional DTCs stored?

--

Go to the Applicable DTC Table

Go to Diagnostic Aids

5
  1. Resume switch signal circuit is shorted to voltage.
  2. Repair as necessary.

Is the action complete?

--

Go to Step 8.

--

6

Replace the faulty PCM.

Important: If the PCM is faulty, the new PCM must be programmed. Go to Powertrain Control Module Replacement/Programming .

Is the action complete?

--

Go to Step 7

--

7
  1. Using the Scan Tool, select DTC, Clear Info.
  2. Start engine and idle at normal operating temperature.
  3. Select DTC, Specific, then enter the DTC number which was set.
  4. Operate vehicle within the conditions for setting this DTC as specified in the supporting text.

Does the Scan Tool indicate that this diagnostic Ran and Passed?

--

Go to Step 8

Go to Step 2

8

Using the Scan Tool, select Capture Info, Review Info.

Are any DTCs displayed that have not been diagnosed?

--

Go to the Applicable DTC Table

System OK