The design of the passlock™ system is to prevent vehicle theft by disabling the engine unless the passlock™ lock cylinder rotates properly by engaging the correct ignition key. The system is similar in concept to the passkey system. However, the passlock™ system eliminates the need for a key mounted resistor pellet. The components of the passlock system are as follows:

The ignition lock cylinder is located at the upper right side of the steering column. The Passlock™ sensor is in the steering column. The Passlock™ sensor is separate from the key and lock cylinder. The key and the lock cylinder work together in order to determine if the proper ignition key was used to start the vehicle.

In the event of an open Class 2 serial data line between the BCM and the VCM/PCM, the vehicle will become fail-enabled if the VCM/PCM has already received the password from the BCM for that ignition cycle (the engine is running). In this event, the following conditions occur:

If a failure in the Class 2 serial data line occurs before the ignition cycle, when the VCM/PCM is not fail-enabled, the following conditions occur:

The lock cylinder and the visible key insert portion of the ignition switch are located at the upper right side of the steering column. The electrical switching portion of the assembly is separate from the key and lock cylinder. The electrical switch portion is hidden inside the steering column. The electrical switch portion and the key and lock cylinder synchronize and work in conjunction through the action of the mechanical assembly between the 2 parts.

The passlock™ sensor is inside the upper right side of the steering column. The passlock™ sensor contains 2 hall effect sensors. The tamper hall effect sensor is on the top. The security hall effect sensor is under the tamper hall effect sensor. Both of the hall effect sensors monitor the magnet of the lock cylinder through an opening. The tamper hall effect sensor is physically placed on top of the security hall effect sensor. The placement enables the tamper hall effect sensor to engage first if an intruder attempts to bypass the passlock™ sensor by placing a large magnet around that area of the steering column. There is a tamper resistor inside the passlock™ sensor in order to help prevent tamper to the system. Passlock™ equipped vehicles have a selection of 10 different security resistors ranging up to 13K ohms. Install any of the security resistors inside the passlock™sensor in order to generate a unique passlock™ code. All 10 combinations of the passlock™ sensor have the same part number. However, you cannot simply replace the passlock™ sensor and expect the system to operate properly. Always start by performing the Diagnostic System Check first and following the instructions.

The Body Control Module (BCM) contains the theft deterrent system logic. The BCM reads the passlock™ data from the passlock™ sensor. If the passlock™ data is correct, the BCM will pass theft. The BCM will then transmit the code password to the VCM/PCM.

During the tamper mode the vehicle may start. The vehicle will then stall. If the BCM receives the wrong passlock™ data, the VTD will immediately go into the tamper mode. The tamper mode will lock-out the vehicle fuel injectors for 10 minutes. The SECURITY indicator will flash while the VTD is in the tamper mode.

If the passlock  sensor sends a correct password to the BCM when the ignition is in the ON position, the BCM will send a fuel enable signal to the VCM/PCM. The VCM will not disable the fuel due to any BCM message for the remainder of the ignition cycle.

The SECURITY indicator is on the instrument cluster. If the SECURITY indicator flashes or if the SECURITY indicator lights continuously during the vehicle operation, refer to the system diagnosis.

The VCM/PCM communicates with the BCM over the Class 2 serial data line. When the BCM determines a no start condition, it sends a Class 2 serial data password to the VCM/PCM in order to disable the fuel injection system. If the BCM receives the expected voltage from the Passlock™ sensor, the BCM sends a Class 2 serial data password to the VCM/PCM in order to enable the fuel injection system. The VCM/PCM then allows the vehicle to start correctly. If the Class 2 serial data password from the BCM to the VCM is not within the Vehicle Security Status Message, the fuel injectors will shut OFF during a start attempt. The SECURITY telltale will be illuminated for. If the VCM/PCM does not receive the same password from the BCM as the last learned one, the vehicle will start and then stalls due to the Fuel Lockout.

The Passlock™ system has a lockout cycle of approximately 10 minutes. Once the vehicle is in the lockout cycle, the vehicle remains in the lockout cycle for 10 minutes, even if the ignition switch is turned from the RUN position to the OFF position.

The Passlock™ system uses the lockout cycle in order to synchronize all of the Passlock™ components when any Passlock™ related part is changed. The Passlock™ system requires 3 consecutive lockout cycles in order to complete the 30 minute learn procedure for a changed component.

The design of the passlock™ system is to prevent theft even if the various theft deterrent parts change. The parts that can no longer be changed without the possibility of going into a tamper mode are:

If you replace any of these parts the vehicle may start and stall for 10 minutes. This is the long tamper mode. If this occurs, the system must go through a long tamper mode cycle. During this time the SECURITY indicator will be flashing for the full 10 minutes and the DTC B3031 will be set. The BCM and the VCM/PCM require the full 10 minutes in order to complete a learn cycle. The ignition switch must remain in the RUN position until the SECURITY indicator stops flashing. You will need to repeat the cycle if the ignition switch does not remain in the RUN position. When replacing any of the above parts it is recommended to perform one of the following procedures: