GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2000 🢒 Jimmy - 4WD 🢒 Driveline/Axle 🢒 Transfer Case - NVG 236 (Two Speed Automatic) 🢒 DTC C0362 4LO Discrete Output Circuit High

Object Number: 564266 Size: MF
Transfer Case Control Components
Transfer Case Control Schematics

Circuit Description

The 4WD LO circuit is used to inform the PCM/VCM when the transfer case has been placed into 4WD LO mode. The PCM/VCM supplies the circuit with a 12 V signal. When the transfer case is placed into 4WD LO, the transfer case shift control module pulls the 12 V signal low which is then sensed by the PCM/VCM.

This DTC detects an internal module fault or a short to voltage on the 4WD LO signal feed circuit.

Conditions for Setting the DTC
    • After the system turns the output on, (grounding the 4WD LO Signal Feed Circuit), and reads back a high voltage, the DTC is set. The system will not attempt it again during that ignition cycle.
    • The transfer case shift control module reads back a high voltage when a low voltage is expected on the 4WD LO Signal Feed Circuit.

Action Taken When the DTC Sets
    • May affect the transmission shift points.
    • The SERVICE indicator (AWD/4WD) lamp will be latched on for the remainder of the current ignition cycle.

Conditions for Clearing the DTC
    • The transfer case shift control module will clear the DTC if the condition for setting the DTC no longer exits.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History DTCs can be cleared using a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Tests the 4WD LO circuit for voltage.

    2.

  2. Tests the 4WD LO circuit for a short to voltage.

    3.

  3. Tests the 4WD LO circuit for an open or high resistance.

    4.

  4. Repairs the 4WD LO circuit for a short to voltage.

DTC C0362 4LO Discrete Output Circuit High

Step

Action

Value(s)

Yes

No

1

Was the Transfer Case Diagnostic System Check performed?

--

Go to Step 2

Go to Diagnostic System Check

2

  1. Turn the ignition OFF.
  2. Disconnect the transfer case shift control module.
  3. Connect a DMM between the 4WD LO circuit and ground.
  4. Turn the ignition ON with the engine OFF.

Does the DMM indicate battery voltage?

--

Go to Step 3

Go to Step 4

3

  1. Turn the ignition OFF.
  2. Disconnect the powertrain control module.
  3. Turn the ignition ON with the engine OFF.

Does the DMM continue to show battery voltage?

--

Go to Step 5

Go to Step 7

4

Test the 4WD LO circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Was the condition found and corrected?

--

Go to Step 8

Go to Step 6

5

Repair the 4WD LO circuit for a short to voltage. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Step 8

--

6

Replace the powertrain control module. Refer to Powertrain Control Module Replacement/Programming for the 2.2L engine, Powertrain Control Module Replacement/Programming for the 2.2L (L43) engine, or VCM Replacement/Programming for the 4.3L engine.

Is the replacement complete?

--

Go to Step 8

--

7

Replace the transfer shift case control module. Refer to Transfer Case Shift Control Module Replacement .

Is the replacement complete?

--

Go to Step 8

--

8
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK