GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2001 🢒 Jimmy - 4WD 🢒 Engine 🢒 Engine Controls - 4.3L 🢒 DTC P0420 or P0430

Circuit Description

In order to maintain a reasonably low emissions of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx), the engine controls system uses a three-way catalytic converter. The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas. This reaction converts them into harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting the NOx into nitrogen. The powertrain control module (PCM) monitors this process using bank 1 heated oxygen sensor (HO2S)  2. Bank 1 HO2S  2, located in the exhaust stream past the three-way catalytic converter, produces an output signal which indicates the oxygen storage capacity of the catalyst. This determines the catalysts ability to convert exhaust emissions effectively. If the catalyst is functioning correctly, the bank 1 HO2S 2 signal will be far less active than that produced by bank 1 HO2S  1. This indicates that the three-way catalytic converters oxygen storage capacity is operating at a threshold considered acceptable.

When the conditions for running this diagnostic trouble code (DTC) are met, the following occurs:

    • The powertrain control module (PCM) captures the current rear HO2S rich or lean status.
    • The air fuel ratio transitions from rich to lean or lean to rich depending on the capture rear HO2S rich or lean status.
    • The air fuel ratio transitions a second time opposite the first air fuel ratio transition.
    • The PCM captures the response time, the time the HO2S goes from below 300 mV to above 600 mV and from 600 mV to below 300 mV, of the front and rear heated oxygen sensors when the air fuel ratio transitions occurred.
    • The PCM measures the time the HO2S takes the rear HO2S voltage to cross a reference rich or lean threshold minus the time the HO2S takes the front HO2S voltage to cross the same rich or lean threshold. The time difference from the front and rear HO2S is the oxygen storage capacity of the catalyst. This DTC sets if the time exceeds a predetermined threshold.

Conditions for Running the DTC
    • DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0171, P0172, P0200, P0300, P0335, P0336, P0341, P0342, P0343, P0351, P0401, P0404, P0405, P0410, P0418, P0440, P0442, P0443, P0446, P0449, P0500, P0502, P0503, P0506 , P0507, 0704, P0706, P0711, P0712, P0716, P0719, P0724, P0740, P0741, P0742, P0748, P0751, P0752, P0753, P0756, P0757, P0758, P1112, P1114, P1115, P1121, P1122, P1336, P1345, P1404, P1860, P1870, or P1875 are not set.
    • The engine operating longer than 400 seconds.
    • The engine coolant temperature (ECT) is between 70-120°C (158-248°F).
    • The intake air temperature (IAT) is between -15 to +167°F (5-75°C).
    • The engine speed is more than 1,300 RPM for a minimum of 9 seconds since the end of the last idle test.
    • The barometric pressure (BARO) is more than 74 kPa.
    • The fuel system is operating in Closed Loop.

Conditions for Setting the DTC

The PCM determines the oxygen storage capability of the catalytic converter has degraded below a calibrated threshold.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. Before replacing the three-way catalytic converter, correct any conditions which may have damaged the catalyst.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Are any other DTCs set?

Go to Diagnostic Trouble Code (DTC) List

Go to Step 3

3
  1. Inspect for the following conditions:
    2. • Verify that the three-way catalytic converter is an original equipment part.
    • Inspect the three-way catalytic converter for damage, such as dents, severe discoloration caused by excessive temperature, holes, etc. Refer to Exhaust System Inspection in Engine Exhaust.
    • Insure that the internal three-way catalytic converter rattle caused by damaged catalyst is not present.
    • Inspect the exhaust system for leaks, damage, or loose or missing hardware, in area from converter to HO2S 2 primarily. Refer to Exhaust System Inspection in Engine Exhaust.
    • Insure that the HO2S 1 and the HO2S 2 are secure and that the pigtails and wiring are not damaged or contacting the exhaust. Refer to Exhaust System Inspection in Engine Exhaust.
  2. Repair conditions, as necessary.

Did you find and correct the condition?

Go to Step 5

Go to Step 4

4

Replace the catalytic converter. Refer to Catalytic Converter Replacement in Engine Exhaust.

Is the action complete?

Go to Step 5

--

5
  1. Select the Diagnostic Trouble Code (DTC) option and the Clear DTC Information option using the scan tool.
  2. Idle the engine at the normal operating temperature.
  3. Select the Diagnostic Trouble Code (DTC) option and the Specific DTC option, then enter the DTC number using the scan tool.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text, if applicable.

Does the scan tool indicate that this test ran and passed?

Go to Step 6

Go to Step 2

6

Select the Capture Info option and the Review Info option using the scan tool.

Does the scan tool display any DTCs that you have not diagnosed?

Go to Diagnostic Trouble Code (DTC) List

System OK