Application | Specification | |
|---|---|---|
Metric | English | |
A/C Compressor Low Pressure Switch (4.3 L) | 5 N·m | 44 lb in |
A/C Compressor Mounting Bolts (2.2 L) | 50 N·m | 37 lb ft |
A/C Compressor Mounting Bolts (4.3 L) | 50 N·m | 37 lb ft |
A/C Compressor Rear Bracket Bolt (2.2 L) | 25 N·m | 18 lb ft |
A/C Compressor Shaft Nut (V7) | 17.5 N·m | 13 lb ft |
A/C Refrigerant Filter Retaining Nuts | 15 N·m | 11 lb ft |
A/C Refrigerant Pressure Sensor (2.2 L) | 4.8 N·m | 42 lb in |
Accumulator Clamp Screw/Bolt | 10 N·m | 88 lb in |
Accumulator to Evaporator Fitting | 28 N·m | 21 lb ft |
Air Distributor Duct Mounting Screw/Bolt | 1.9 N·m | 17 lb in |
Air Inlet Assembly Mounting Stud | 4.5 N·m | 40 lb in |
Blower Assembly Mounting Nut (RPO C42) | 4.5 N·m | 40 lb in |
Blower Assembly Mounting Screw/Bolt (RPO C42) | 4.5 N·m | 40 lb in |
Blower Assembly Mounting Stud (RPO C42) | 4.5 N·m | 40 lb in |
Blower Motor Access Cover Screw/Bolt (RPO C60 and C68)) | 2.5 N·m | 22 lb in |
Blower Motor Access Cover Screw/Bolt (Utility Only) | 1.9 N·m | 17 lb in |
Blower Motor Mounting Bolts | 4.5 N·m | 40 lb in |
Blower Motor Relay Bracket Mounting Screw/Bolt | 1.9 N·m | 17 lb in |
Blower Motor Resistor Mounting Screw/Bolt | 1.9 N·m | 17 lb in |
Body Harness Connector (C203) Support Bracket Mounting Nuts | 9.0 N·m | 80 lb in |
Compressor Discharge Hose to Condenser Fitting | 28 N·m | 21 lb ft |
Compressor Pressure Relief Valve (2.2 L) | 9 N·m | 80 lb in |
Compressor Pressure Relief Valve (4.3 L) | 9 N·m | 80 lb in |
Compressor Suction/Discharge Hose to Compressor Bolt | 33 N·m | 24 lb ft |
Compressor Suction Hose to Accumulator Fitting | 48 N·m | 35 lb ft |
Condenser Insulator Retaining Screw/Bolt | 1.9 N·m | 17 lb in |
Electric Actuator (Temperature) Retaining Screw/Bolt | 1.9 N·m | 17 lb in |
Evaporator and Blower Module Heat Shield Mounting Screw/Bolt (utility only) | 2.2 N·m | 19 lb in |
Evaporator and Blower Module Mounting Nut | 4.5 N·m | 40 lb in |
Evaporator and Blower Module Mounting Screw/Bolt | 4.5 N·m | 40 lb in |
Evaporator Case Section to Blower Case Section Retaining Screw/Bolt | 1.9 N·m | 17 lb in |
Evaporator Tube Clip Screw/Bolt | 1.9 N·m | 17 lb in |
Evaporator Tube to Condenser Fitting | 28 N·m | 21 lb ft |
Evaporator Tube to Evaporator Fitting | 28 N·m | 21 lb ft |
Floor Air Outlet Mounting Screw/Bolt (Pickup Only) | 1.9 N·m | 17 lb in |
Heater Core Access Cover Screws | 1.9 N·m | 17 lb in |
Heater Inlet and Outlet Hoses Bracket Bolt to Generator (4.3 L) | 25 N·m | 18 lb ft |
Heater Inlet and Outlet Hoses Bracket Bolt to Generator Mounting Bracket (4.3 L) | 50 N·m | 37 lb ft |
Heater Inlet Hose Fitting at Intake Manifold (4.3 L ) | 23.5 N·m | 17 lb ft |
Heater Outlet Hose Bracket Bolt (2.2 L) | 25 N·m | 18 lb ft |
Heater/Vent Module Mounting Nut | 4.5 N·m | 40 lb in |
Heater/Vent Module Mounting Screw/Bolt | 4.5 N·m | 40 lb in |
Throttle Control Cable Bracket Nut | 12 N·m | 106 lb in |
