Circuit Description
The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high, and decreases the signal voltage as the engine runs learner. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.
The HO2S contains heater that is necessary in order to quickly warm the sensor to operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. The control module also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or lean out the mixture, when the HO2S detects a rich exhaust condition.
This diagnostic trouble code (DTC) is designed to detect an HO2S voltage that remains at a high voltage for more than a specified number of seconds during the test conditions.
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0200, P0300, P0440, P0442, P0446, P0452, P0453, or P1441 are not set. |
| • | The ignition 1 signal is between 9-18 volts. |
| • | The fuel tank level remaining is more than 10 percent. |
| • | The loop status is closed. |
| • | Intrusive tests are not in progress. |
| • | Scan tool output controls are not active. |
Rich Test Enable
| • | The air fuel ratio is between 14.5:1-14.7:1. |
| • | The throttle position (TP) is between 3-70 percent. |
Decel Fuel Cut-off Test Enable
| • | Decel fuel cut-off (DFCO) is active. |
| • | The above condition is met for 5 second. |
Conditions for Setting the DTC
Rich Test
The HO2S voltage is more than 975 mV for 99 seconds.
Decel Fuel Cut-off Test
The HO2S voltage is more than 200 mV for 10 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
| • | The control module commands Open Loop. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
Important: Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing or replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.
| • | Inspect the HO2S electrical connections for evidence of water intrusion. Water present in the connector causes the B+ supply to the heater to bleed over to the signal circuit. |
| • | Inspect the fuel pressure. The system goes rich if the pressure is too high. The PCM compensates for some increase. If the fuel pressure is too high, a DTC may set. Refer to Fuel System Diagnosis . |
| • | Inspect for a rich injector. Perform the Injector Balance Test. Refer to Fuel Injector Balance Test with Tech 2 or Fuel Injector Balance Test with Special Tool . |
| • | Inspect for a leaking injector. Refer to Fuel System Diagnosis . |
| • | Inspect the fuel pressure regulator. Inspect the vacuum line going to the fuel pressure regulator for evidence of fuel. Refer to the Fuel System Diagnosis . |
| • | Inspect the evaporative emissions (EVAP) canister purge. Inspect the canister for fuel saturation. If the canister is full of fuel, check the canister control and the hoses. Refer to Evaporative Emission Control System Description . |
| • | Inspect the mass air flow (MAF) sensor. Disconnect the MAF sensor and see if the rich condition is corrected. If the condition is corrected, check for proper installation. If the sensor is correctly installed, replace the sensor. If the sensor is installed backwards, the system goes rich. The plastic portion of the sensor has arrows cast that indicate the proper air flow direction. The arrows must point toward the engine. |
| • | Inspect the HO2S wires. An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provide the supply of oxygen. Inspect the HO2S wires and connections for breaks or for contamination. Refer to Heated Oxygen Sensor Wiring Repairs in Wiring Systems. |
| • | Inspect the throttle position (TP) sensor. An intermittent TP sensor output causes the system to go rich, due to a false indication of the engine accelerating. For an intermittent condition, refer to Symptoms - Engine Controls . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Monitor the HO2S voltage of the opposite bank sensor. If the voltage activity of the opposite bank sensor is similar to the voltage activity of the suspect sensor, check for rich conditions that would affect both cylinder banks. An opposite bank sensor with normal HO2S voltage activity indicates the suspect HO2S is defective or a rich condition exists only on the suspect HO2S cylinder bank.
-
An HO2S contaminated by silicon will have a white, powdery deposit on the portion of the HO2S that is exposed to the exhaust stream. The usual cause of silica contamination is the use of unapproved silicon RTV engine gasket material or the use of silicon based sprays or fluids within the engine. If the cause of this contamination is not corrected, the replacement HO2S will also get contaminated.
Step | Action | Values | Yes | No | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||||||||||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||||||||||||||||
2 |
Is the HO2S voltage fixed at more than the specified value? | 975 mV | Go to Step 4 | Go to Step 3 | ||||||||||||||||||||||
3 |
Did you find and correct the condition? | -- | Go to Step 10 | Go to Diagnostic Aids | ||||||||||||||||||||||
4 |
Is the HO2S voltage within the specified range? | 351-551 mV | Go to Step 5 | Go to Step 6 | ||||||||||||||||||||||
Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | |||||||||||||||||||||||
6 |
Is the voltage more than the specified value? | 20 mV | Go to Step 7 | Go to Step 9 | ||||||||||||||||||||||
7 |
Important: The sensor may be damaged if the circuit is shorted to a voltage source. Repair the short to voltage in the HO2S high signal circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 10 | -- | ||||||||||||||||||||||
|
Important: Before replacing a contaminated HO2S, determine and repair the cause of the contamination. Replace the affected HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 . Did you complete the replacement? | -- | Go to Step 10 | -- | |||||||||||||||||||||||
9 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||||||||||||||||
10 |
Does the DTC run and pass? | -- | Go to Step 11 | Go to Step 2 | ||||||||||||||||||||||
11 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |||||||||||||||||||||||
