REAR DOOR WATERLEAKS (INST. DEFLECTORS, INSULATORS, & SEA. GMC Truck S15 Pickup

REVISION: 03/04/94

THIS BULLETIN IS BEING REVISED TO CHANGE THE SERVICE PROCEDURE, PARTS INFORMATION, ARTWORK, AND TO INCLUDE THE 1993 MODEL YEAR. PREVIOUS DIVISIONAL PUBLICATION NUMBERS WERE:

DIV BULLETIN # PUBLISH DATE CHEVROLET 92-352-10 5/14/93 GMC TRUCK 92-10A1-157 6/08/93 GM CANADA 93-10-209 8/02/93 OLDSMOBILE 92-T-172 6/21/93 ----------------------------------------------------------------------

SUBJECT: REAR DOOR WATER LEAKS (INSTALL DEFLECTORS, INSULATORS, AND SEALER)

MODELS: 1991-93 CHEVROLET AND GMC S/T FOUR DOOR UTILITY TRUCKS 1991-93 OLDSMOBILE BRAVADA

CONDITION:

SOME OWNERS MAY COMMENT ABOUT REAR DOOR WATER LEAKS.

CAUSE:

THIS CONDITION MAY OCCUR WHEN WATER PATHS IN THE DOOR DEVELOP, ALLOWING WATER TO DRAIN INTO THE INSIDE OF THE VEHICLE.

CORRECTION:

TO CORRECT THIS CONDITION, IT IS NECESSARY TO REPLACE THE DOOR INNER PANEL PLASTIC WATER DEFLECTOR, INSTALL A FOAM WATER DEFLECTOR TO THE DOOR, ADD A FOAM PATCH BETWEEN THE TOP FORWARD CORNER OF THE FIXED GLASS, THE RUN CHANNEL AND THE DIVIDER BAR ASSEMBLY AND INSTALL SEALER IN THE CUT OUT AREA ALONG THE TOP OF THE DOOR AT THE DIVIDER BAR ATTACHMENT.

SERVICE PROCEDURE:

1. REMOVE TWO FASTENING SCREWS FROM THE ARMREST.

2. REMOVE THE DOOR PILLAR MOLDING.

3. REMOVE THE MANUAL WINDOW HANDLE, IF EQUIPPED.

4. REMOVE THE DOOR TRIM PANEL (HELD IN PLACE WITH SIX PLASTIC RETAINERS) USING TRIM PANEL REMOVAL TOOL J-38778, OR EQUIVALENT.

5. REMOVE THE ARMREST BRACKET.

6. CAREFULLY REMOVE THE DOOR INNER PANEL PLASTIC WATER DEFLECTOR (FIGURE 1, ITEM B) BY PULLING THE WATERPROOF SEALING TAPE FROM THE DEFLECTOR AND BREAKING THE BOND BETWEEN THE SEALER AND THE DOOR WITH A FLAT-BLADED TOOL. DISCARD THE PLASTIC DEFLECTOR.

7. CLEAN THE AFFECTED SHEET METAL PANEL AREA USING EITHER A 50-50 MIXTURE (BY VOLUME) OF WATER AND ISOPROPYL ALCOHOL; OR FLASH NAPHTHA, OR EQUIVALENT (PROCURE LOCALLY). ALLOW TO DRY THOROUGHLY.

8. INSTALL A WATER DEFLECTOR (P/N 15603079) (FIGURE 1, ITEM A) ON THE DOOR INNER PANEL (ONE PER SIDE) AS SHOWN IN FIGURE 1. THE BOTTOM PORTION OF THE DEFLECTOR SHOULD BE POSITIONED IN THE DOOR PANEL ACCESS OPENING.

9. REMOVE THE FIXED GLASS ASSEMBLY. REFER TO APPLICABLE S/T MODEL SERVICE MANUAL, SECTION 10A1-DOORS, REAR DOOR WINDOW REPLACEMENT.

10. INSTALL INSULATOR (P/N 15675045) BETWEEN THE TOP FORWARD CORNER OF THE FIXED GLASS RUN CHANNEL AND DIVIDER BAR ASSEMBLY (FIGURE 2).

11. REINSTALL THE FIXED GLASS ASSEMBLY.

12. CLEAN THE CUT OUT AREA LOCATED ON THE TOP OF THE DOOR ABOVE THE DIVIDER BAR ATTACHMENT (APPROX. 3 IN. LONG) WITH EITHER A 50-50 MIXTURE (BY VOLUME) OF WATER AND ISOPROPYL ALCOHOL; OR FLASH NAPHTHA, OR EQUIVALENT. ALLOW TO DRY THOROUGHLY.

13. USE A SUFFICIENT QUANTITY OF 3M ULTRA PRO AUTO BODY SEALANT (CLEAR), VENDOR PART NUMBER 051135-08302 OR EQUIVALENT AND FILL THE CUT OUT AREA LOCATED ON THE TOP OF THE DOOR ABOVE THE DIVIDER BAR.

14. SMOOTH SEALER.

15. INSTALL A NEW DOOR INNER PANEL PLASTIC WATER DEFLECTOR (P/N 15689413/15689414) (FIGURE 1, ITEM B). USE STRIP CAULKING AS A SEALANT BETWEEN THE DEFLECTOR AND THE DOOR AS NEEDED. WATERPROOF SEALING TAPE SHOULD ALSO BE USED TO HELP SECURE THE DEFLECTOR.

16. REINSTALL THE ARMREST BRACKET. TIGHTEN THE ARMREST BRACKET BOLTS TO 9.5 N.M (84 LBS. IN.).

17. REINSTALL THE DOOR TRIM PANEL.

18. REINSTALL THE DOOR PILLAR MOLDING.

19. REINSTALL THE ARMREST.

SERVICE PARTS INFORMATION:

PART NUMBER DESCRIPTION VEHICLE QTY.

15603079 DEFLECTOR ASM.-REAR S/D WATER 1/SIDE 15675045 INSULATOR PATCH-WINDOW 1/SIDE 15689413 DOOR INNER PANEL PLASTIC WATER DEFLECTOR-LH 1 15689414 DOOR INNER PANEL PLASTIC WATER DEFLECTOR-RH 1 * 051135-08302 3M ULTRA PRO AUTO BODY SEALANT 5 OZ. TUBE (CLEAR)

(*) PROCURE FROM YOUR LOCAL 3M AUTOMOTIVE DISTRIBUTOR.

PARTS ARE CURRENTLY AVAILABLE FROM GMSPO.

WARRANTY INFORMATION:

FOR VEHICLES REPAIRED UNDER WARRANTY USE:

LABOR OP. DESCRIPTION LABOR TIME

T-7641 RIGHT 0.3 HRS. T-7642 LEFT 0.3 HRS.

NOTE: LABOR OPERATION IS CODED TO BASE VEHICLE COVERAGE IN THE WARRANTY SYSTEM.

FIGURES: 2

CAPTIONS: FIGURE 1 - REAR DOOR INNER PANEL FIGURE 2 - REAR DOOR ASSEMBLY

Object Number: 84167 Size: FS

Object Number: 83129 Size: FS

GENERAL MOTORS BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THOSE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE EQUIPMENT, TOOLS, SAFETY INSTRUCTIONS AND KNOW-HOW TO DO A JOB PROPERLY AND SAFELY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION. SEE A GENERAL MOTORS DEALER SERVICING YOUR BRAND OF GENERAL MOTORS VEHICLE FOR INFORMATION ON WHETHER YOUR VEHICLE MAY BENEFIT FROM THE INFORMATION.