Circuit Description
The VCM supplies a voltage of about 0.45 volt (450 mV) between the HO2S High and HO2S Low circuits. (If measured with a megohm digital voltmeter, this may read as low as 0.32 volt.) The Heated Oxygen Sensor (HO2S Bank 1 Sensor 1) varies the voltage within the range of about 1.0 volt (1000 mV) if the exhaust is rich, down to about 0.10 volt (100 mV) if the exhaust is lean. This DTC is a type A DTC.
The Sensor is like an open circuit and produces no voltage when it is below 360°C (600°F). This DTC or a cold sensor causes an Open Loop operation. The DTC P0132 determines if the HO2S sensor or the circuit is shorted to high by checking for a rich condition during a steady throttle.
Conditions for Setting the DTC
| • | No TP sensor DTCs |
| • | No EVAP DTCs |
| • | No IAT sensor DTCs |
| • | No MAP sensor DTCs |
| • | No ECT sensor DTCs |
| • | No MAF sensor DTCs |
| • | No intrusive test in progress |
| • | No device controls active |
| • | The system voltage measures at least 9.0 volts |
Test Enable (Rich Test)
| • | Closed Loop |
| • | Air to fuel ratio is at least 14.5 but less than 14.8 |
| • | The TP is greater than 0% but less than 50% |
| • | The above must be met for 5 seconds |
| • | HO2S (Bank 1, Sensor1) DTCs not active since code clear |
| • | The HO2S (Bank 1, Bank 1) voltage measures greater than 0.976 volts (976 mV) |
Test Enable (DFCO Rich Test)
| • | Decel Fuel cutoff mode is active |
| • | Closed Loop |
| • | The time elapsed is at least 2 seconds |
| • | HO2S (Bank 1, Sensor 1) DTCs not active since code clear |
| • | The HO2S (Bank 1, Sensor 1) voltage measures greater than 0.468 volts (486 mV) |
Action Taken When the DTC Sets
A current DTC P0132 causes the system to operate in the Open Loop. With a current DTC P0132 set, the MIL turns ON after 1 test failure.
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Important: Never solder the HO2S wires. For proper wire and connector repair, refer to Wiring Repairs .
Check the following items:
| • | The fuel pressure: If the pressure is too high, the system will run rich. The VCM can compensate for some increase; however, if the pressure gets too high, the DTC P0132 may set. Refer to Fuel System Pressure Test . |
| • | A rich injector. Preform a poppet nozzle test. Refer to Fuel Injector Balance Test . |
| • | A leaking injector. Refer to Fuel Injector Balance Test . |
| • | Fuel contaminated oil |
| • | EVAP canister purge: Check for a fuel saturation. If full of fuel, check the canister control and hoses. |
| • | Leaking fuel pressure regulator diaphragm by checking the vacuum line to the regulator for fuel. |
| • | The TP sensor: An intermittent TP sensor output causes the system to run rich due to a false indication of the throttle moving. |
| • | False rich indication due to silicon contamination of the heated oxygen sensor. A DTC P0132 accompanied by a lean driveability conditions and a powdery white deposit on the sensor indicates a false rich indication. |
| • | If the HO2S (Bank 1, Sensor 1) is internally shorted, the HO2S (Bank 1, Sensor 1) voltage displayed on a scan tool will be over 1.0 volt (1000 mV). |
Test Description
The number below refers to the step number on the diagnostic table.
-
This test determines if the conditions exist in order to set the DTC P0132.
-
If the HO2S (Bank 1, Sensor 1) is internally shorted, the HO2S (Bank 1, Sensor1) voltage displayed on a scan tool will be over 1.0 volt (1000 mV).
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records data. This data will be lost when the Clear DTC Information function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Does the scan tool data display indicate the HO2S (Bank 1, Sensor 1) voltage fixed above the specified value? | 1200 RPM 0.976 V (976 mV) | |||
Does the scan tool data display indicate the HO2S (Bank 1, Sensor 1) voltage near the specified value? | 0.40 V (400 mV) | |||
4 | The DTC is intermittent. Are any additional DTCs set? | -- | Go to the applicable DTC table | Go to Diagnostic Aids |
5 |
Was the HO2S (Bank 1, Sensor 1) Signal circuit shorted? | -- | ||
6 | Replace the HO2S (Bank 1, Sensor 1). Refer to Heated Oxygen Sensor (HO2S) Replacement . Is the action complete? | -- | -- | |
7 | Replace the VCM. Important: When replacing the VCM, the new VCM will need to be programmed. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |
8 |
Does the scan tool indicate that this diagnostic ran and passed? | -- | ||
9 | Using the scan tool, select the Capture Info and the Review Capture Info functions. Are there any DTCs displayed that have not been diagnosed? | -- | Go to the applicable DTC table | System OK |
