Circuit Description
The body control module (BCM) monitors the voltage and controls the ground of the courtesy lamp relay on CKT 690. When the BCM receives a signal from a mini-wedge (door jamb switch), a signal to unlock the doors from the remote control door lock receiver module or the dome lamp switch being turned ON, the BCM will ground the relay and turn ON the courtesy lamps.
Conditions for Running the DTC
| • | The ignition switch in the OFF position. |
| • | Unlock doors from the remote control door lock key fob, or open any door, or turn ON the dome lamp from the switch (thumbwheel). |
Conditions for Setting the DTC
| • | All courtesy lamps OFF. |
| • | CKT 690 is open or shorted to ground. |
| • | CKT 1732 is open. |
| • | All the above conditions must be met for 0.5 seconds. |
Action Taken When the DTC Sets
| • | The courtesy lights will not function if the circuit is open. |
| • | The courtesy lights will be ON at all times if circuit is shorted to ground. |
Conditions for Clearing the MIL/DTC
| • | This DTC will clear immediately after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
| • | Use a scan tool in order to clear history and current DTCs. |
Diagnostic Aids
| Important: Use the appropriate probe from the J 35616 connector test adapter kit for any probing of the electrical components mentioned in this table to avoid damage to the terminals. |
| • | Perform a visual inspection for loose or poor connections at all related components |
| • | Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Listen for an audible click when the courtesy lamp relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
Tests for voltage at the coil side of the courtesy lamp relay. The CTSY fuse supplies power to the coil side of the courtesy lamp relay.
-
Verifies that the body control module is providing ground to the courtesy lamp relay.
-
Tests if ground is constantly being applied to the courtesy lamp relay.
-
After replacement of the BCM you must calibrate the new module for proper operation.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting System Diagnostic System Check? | -- | Go to Step 2 | |
Does the courtesy lamp relay turn ON and OFF with each command? | -- | Go to Diagnostic Aids | Go to Step 3 | |
Does the test lamp illuminate? | -- | Go to Step 4 | Go to Step 10 | |
Does the test lamp turn ON and OFF with each command? | -- | Go to Step 8 | Go to Step 5 | |
Does the test lamp remain illuminated with each command? | -- | Go to Step 7 | Go to Step 6 | |
6 | Test the control circuit of the courtesy lamp relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the control circuit of the courtesy lamp relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
8 | Inspect for poor connections at the courtesy lamp relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
9 | Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Repair the coil side feed circuit of the courtesy lamp relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 13 | -- |
11 | Replace the courtesy lamp relay. Did you complete the replacement? | -- | Go to Step 13 | -- |
Did you complete the replacement? | -- | Go to Step 13 | -- | |
13 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
