Circuit Description
The vehicle speed sensor (VSS) assembly provides vehicle speed information to the vehicle control module (VCM). The VSS assembly is a permanent magnet (PM) generator. The PM generator produces a pulsing AC voltage as rotor teeth on the transmission output shaft pass through the sensor's magnetic field. The AC voltage level and the number of pulses increase as the speed of the vehicle increases. The VCM converts the pulsing voltage to vehicle speed. The VCM uses the vehicle speed signal to determine shift timing and torque converter clutch (TCC) scheduling.
When the VCM detects a low vehicle speed when there is a high engine speed in a drive gear range, then DTC P0502 sets. DTC P0502 is a type B DTC.
Conditions for Running the DTC
| • | No MAP sensor DTCs P0107 or P0108. |
| • | No TP sensor DTCs P0122 or P0123. |
| • | No TFP manual valve position switch DTC P1810. |
| • | The engine vacuum is 0-105 kPa. |
| • | The engine torque is 40-400 ft lb. |
| • | The TP angle is greater than 20%. |
| • | The engine speed is greater than 3000 RPM. |
| • | The transmission is not in PARK or NEUTRAL. |
Conditions for Setting the DTC
The transmission output speed is less than 150 RPM for 2.5 seconds.
Action Taken When the DTC Sets
| • | The VCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The VCM commands second gear only. |
| • | The VCM commands maximum line pressure. |
| • | The VCM inhibits TCC engagement. |
| • | The VCM freezes shift adapts from being updated. |
| • | The VCM records the operating conditions when the Conditions for Setting the DTC are met. The VCM stores this information as Freeze Frame and Failure Records. |
| • | The VCM stores DTC P0502 in VCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The VCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The VCM clears the DTC from VCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the connectors at the VCM, the VSS assembly and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the VSS assembly circuit.
-
This step tests the integrity of the VSS assembly.
-
This step tests the 5-volt and ground circuits of the VCM.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls | |
2 |
Important: Before clearing the DTC, use the Scan Tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the VCM. With the drive wheels rotating, does the Scan Tool Transmission OSS increase with the drive wheel speed? | -- | Go to Diagnostic Aids | |
Does the resistance measure within the specified range? | 1377-3355 ohms (2WD) 976-2354 ohms (AWD) | |||
Does the voltage measure greater than the specified value? | 0.5 volts | |||
5 | Measure the resistance from terminal C1-30 to ground. Does the resistance measure greater than the specified value? | 50 K ohms | ||
Does the voltage measure within the specified range? | 4.0-5.1 volts | |||
7 | Was the voltage measured in Step 6 less than the voltage in the value column? | 4.0 volts | ||
8 |
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
9 | Test the signal circuit (CKT 821) of the VSS assembly for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Diagnostic Aids | |
10 | Test the signal circuit (CKT 821) of the VSS assembly for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
11 |
Did you find and correct the condition? | -- | ||
12 | Replace the VSS assembly. Refer to Vehicle Speed Sensor Replacement . Did you complete the replacement? | -- | -- | |
13 | Replace the VCM. Refer to VCM Replacement/Programming in Engine Controls. Did you complete the replacement? | -- | -- | |
14 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
