Tools Required

J 29714-A Servo Cover Depressor

1. Raise the vehicle. Refer to General Vehicle Lifting and Jacking in General Information.
2. Lower the transmission if needed for clearance. Refer to Transmission Replacement .
3. Install the J 29714-A .



4. Tighten the bolt in order to compress the servo cover.
5. Remove the servo cover retaining ring.
6. Remove the J 29714-A .



7. Remove the servo cover and the O-ring seal. If the servo cover seems to be hung up on the seal, cut and remove the O-ring seal before removing the cover.
8. Remove the 2-4 servo assembly.

Tools Required

J 22269-01 Piston Remover

1. Remove the following parts:

•	The 4th apply piston

•	The servo return spring




2. Remove the following parts:

2.1.	The retainer ring

2.2.	The washer

2.3.	The spring

2.4.	The 2nd apply piston pin




3. Install the J 22269-01 in order to compress the second apply piston.
4. Remove the second apply piston retaining ring.
5. Remove the servo cushion spring retainer and the servo cushion spring.



6. Remove the seals from the cover, the housing, and the pistons.
7. Clean all the parts using solvent.
8. Air dry all the parts.
9. Inspect the pistons for porosity and damage.
10. Inspect the seal grooves for damage.
11. Inspect the cover for porosity and damage.
12. Inspect for nicks, cuts, and binding in the seal grooves. If damage is found, check for the cause of the damage.
13. Inspect the springs for kinks and bending.
14. Inspect the pin for wear and burrs.

Tools Required

J 33037 Band Apply Pin Tool

1. Install the band apply pin and the J 33037 .
2. Install the servo cover retaining ring to secure the tool.



3. Apply 11 N·m (98 lb in) torque. If the white line appears in the gauge slot, the pin length is correct.
4. If the white line is not seen in the slot, replace the pin using the following pin identification:

•	One groove, pin length 65.82--66.12 mm (2.59--2.60 in)

•	Two grooves, pin length 67.23--67.53 mm (2.65--2.66 in)

•	No grooves, pin length 68.64--68.94 mm (2.70--2.71 in)

5. Remove the pin and the J 33037 .



6. Check the 2nd apply piston and the housing dimension.
7. Measure the piston (25) dimension (1)
8. Measure the housing (22) dimension (2)
9. Check the chart for the transmission and piston/housing specifications.

Tools Required

J 22269-01 Piston Remover

1. Install new seals on all the 2-4 servo pistons and the cover.



2. Install the servo cushion spring and the cushion spring retainer in the 2nd apply piston. Use the J 22269-01 in order to compress the second apply piston.
3. Install the second apply piston retaining ring.



4. Install the following parts:

4.1.	The 2nd apply piston pin

4.2.	The spring

4.3.	The washer

4.4.	The retainer ring




5. Install the following parts:

5.1.	The servo return spring

5.2.	The 4th apply piston

Tools Required

J 29714-A Servo Cover Compressor

1. Install the 2-4 servo assembly into the 2-4 servo bore.
2. Install the J 29714-A .



3. Tighten the bolt in order to compress the servo cover.
4. Install the servo cover retaining ring.
5. Remove the J 29714-A from the oil pan flange.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Install the oil pan bolt.

Tighten
Tighten the oil pan bolt to 11 N·m (97 lb in).

7. Lower the vehicle.
8. Check the automatic transmission fluid level and install new automatic transmission fluid as needed. Refer to Transmission Fluid Check and Fluid Capacity .