Circuit Description
The accelerator pedal position (APP) module provides a voltage signal that changes relative to the accelerator pedal position. There are three sensors which are located within the APP module that are scaled differently.
Conditions for Running the DTC
| • | The ignition voltage is greater than 6.4 volts. |
| • | The engine speed is greater than 300 RPM. |
| • | There are no in range faults for APP 1 or APP 2 (the PCM checks for high and low voltage faults). |
Conditions for Setting the DTC
| • | The difference between APP 3 and APP 1 is greater than 0.23 volts [the PCM compares the pre-scaled voltage (internal to PCM)]. |
| • | The difference between APP 3 and APP 2 is greater than 0.50 volts [the PCM compares the pre-scaled voltage (internal to the PCM)]. |
| • | The conditions met for 2 seconds. |
Action Taken When the DTC Sets
| • | The service throttle soon lamp will not illuminate when one APP DTC sets. The PCM will only illuminate the service throttle soon lamp when multiple APP DTCs set. |
| • | The powertrain control module (PCM) records the operating conditions at the time the diagnostic fails. This information is stored in the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn the MIL off after 3 consecutive trips without a fault condition. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if this or any other emission related diagnostic does not report any failures. |
| • | The scan tool Clear Info function was used. |
Diagnostic Aids
There are no driveability issues associated with the APP module unless a DTC is present. The most likely cause of this DTC are poor connections or the sensor itself. The least likely is a PCM problem.
An intermittent may be caused by the following:
| • | Poor connections |
| • | A rubbed through wire insulation |
| • | A broken wire inside of the insulation |
A scan tool reads the APP 3 position in volts. The scan tool should read about 4.0 volts with the throttle closed and the ignition ON or at idle. The voltage should decrease at a steady rate as the throttle is moved toward a wide open throttle (WOT). Also, 90 percent pedal travel is acceptable for correct APP operation. Scan the APP 3 sensor while depressing the accelerator pedal with the engine stopped and the ignition ON. The display should vary from about 4.0 volts when the throttle was closed to about 2.0 volts when the throttle is held at the WOT position.
Test Description
The number(s) below refer to the step number(s) on the Diagnostic Table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: Before clearing any DTCs, use the scan tool Capture Info function to save the Freeze Frame and the Failure records for reference. The control module's data is deleted once the Clear Info function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Are the APP voltages at the specified values (values are listed as APP 1, APP 2, and APP 3 respectively)? | 0.45-0.95 V 4.0-4.5 V 3.6-4.0 V | |||
3 | The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If any additional DTCs are stored, refer to the applicable DTC table(s) first. Are there any additional DTCs stored? | -- | Go to the applicable DTC Table | Go to Diagnostic Aids |
4 |
Is the voltage greater than or equal to the specified value on all of the circuits? | 4.75 V | ||
5 |
Is the test lamp ON (all circuits)? | -- | ||
6 |
Did you perform a repair? | -- | ||
7 | Check the 5 volt reference circuit for a poor connection at the PCM and replace the terminal if necessary. Refer to Wiring Repairs . Did you perform a repair? | -- | ||
8 |
Did you perform a repair? | -- | ||
9 | Replace the APP module. Refer to Accelerator Pedal Position Module Replacement . Is the action complete? | -- | -- | |
10 |
Important: The new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Replace the PCM. Is the action complete? | -- | -- | |
11 |
Does the scan tool indicate the diagnostic Passed? | -- | ||
12 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the Applicable DTC Table | System OK |
