DTC P0712 Transmission Fluid Temperature (TFT) Sensor Circuit Low Input Gas
Circuit Description
The automatic transmission fluid temperature (TFT) sensor is part of the 4L80-E automatic transmission (A/T) wiring harness assembly. The TFT sensor is a resistor, or thermistor, which changes value based on temperature. The sensor has a negative-temperature coefficient. This means that as the temperature increases, the resistance decreases, and as the temperature decreases the resistance increases. The vehicle control module (VCM) supplies a 5-volt reference signal to the sensor on circuit 1227 and measures the voltage drop in the circuit. When the transmission fluid is cold, the sensor resistance is high and the VCM detects high signal voltage. As the fluid temperature warms to a normal operating temperature, the resistance becomes less and the signal voltage decreases. The VCM uses this information to control shift quality and torque converter clutch apply.
If the VCM detects a continuous short to ground in the TFT sensor or signal circuit, then DTC P0712 sets. DTC P0712 is a type D DTC.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The TFT sensor indicates a voltage of less than 0.14 volts. |
| • | All conditions met for 15 seconds. |
Action Taken When the DTC Sets
| • | The VCM does not illuminates the malfunction indicator lamp (MIL). |
| • | The VCM commands increased line pressure. |
| • | The VCM freezes shift adapts. |
| • | The VCM determines a TFT default transmission temperature (TFT) using the following matrix: |
| - | If the engine run time is less than 60 seconds then default TFT equals the intake air temperature (IAT), plus 5 degrees. |
| - | If the engine coolant temperature (ECT) is less than 85°C (185°F) then default TFT equals IAT plus 10 degrees. |
| - | If the ECT is 85°-110°C (185°-230°F) then default TFT equals ECT plus 10 degrees. |
| - | If the ECT is greater than 110°C (230°F) then default TFT is set to 140°C (284°F) and transmission shift pattern is in hot mode |
| - | If ECT and TFT DTCs are both set then default TFT is 140°C (284°F). |
| • | The VCM stores DTC P0712 in VCM history. |
Conditions for Clearing the DTC
| • | A scan tool clears the DTC from VCM history. |
| • | The VCM clears the DTC from VCM history if the vehicle completes 40 warm-up cycles without a non-emission-related diagnostic fault occurring. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the wiring at the VCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Reduced terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation. |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change. |
| • | Test the TFT sensor at various temperatures in order to evaluate the possibility of a skewed (mis-scaled) sensor. Use the Temperature vs Resistance table. A skewed sensor may cause delayed garage shifts or TCC complaints. |
| • | Verify the customer driving habits, trailer towing, weight, or towing in OVERDRIVE. |
| • | First diagnose and clear any engine DTCs or TP sensor codes that are present. Then inspect for any transmission DTCs that may have reset. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground or a skewed sensor by verifying the fault still exists.
-
This step tests for an internal fault within the transmission by creating an open.
-
This step inspects circuit 1227 of the A/T wiring harness assembly for being shorted to ground.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check (4.3L) or Powertrain On Board Diagnostic (OBD) System Check (5.7L) or Powertrain On Board Diagnostic (OBD) System Check (7.4L) | |
2 | Perform the transmission fluid checking procedure. Refer to Transmission Fluid Check . Was the fluid checking procedure performed? | -- | Go to Transmission Fluid Check | |
Important: Before clearing the DTCs, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the VCM. Does the scan tool display a TFT Sensor signal voltage less than the specified value? | 0.14 volts | Go to Diagnostic Aids | ||
Does the scan tool display a TFT Sensor signal voltage greater than the specified value? | 4.92 volts | |||
5 |
Refer to Electronic Component Description . Is the resistance within the specified values? | 16kohms at 10°C (50°F) to 133ohms at 110°C (230°F) | ||
Measure the resistance between terminal L and a good ground on the transmission case. Is the resistance less than the specified value? | 50 kohms | Go to Diagnostic Aids | ||
7 |
Is the resistance less than the specified value? | 50kohms | ||
8 | Replace the TFT sensor. Refer to A/T Fluid Temperature Sensor Replacement. Is the replacement complete? | -- | -- | |
9 | Inspect circuit 1227 (YEL/BLK) for a short to ground. Refer to General Electrical Diagnosis in Wiring Systems. Was a short to ground condition found? | -- | ||
10 | Replace the A/T wiring harness assembly. Refer to Internal Wiring Harness Replacement. Is the replacement complete? | -- | -- | |
11 | Inspect the VCM for faulty connections. Was the condition found? | -- | ||
12 | Replace the VCM. Refer to VCM Replacement/Programming (4.3L) or VCM Replacement/Programming (5.7L) or VCM Replacement/Programming (7.4L) in Engine Controls. Is the replacement complete? | -- | -- | |
13 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
DTC P0712 Transmission Fluid Temperature (TFT) Sensor Circuit Low Input Diesel
Circuit Description
The automatic transmission fluid temperature (TFT) sensor is part of the 4L80-E automatic transmission (A/T) wiring harness assembly. The TFT sensor is a resistor, or thermistor, which changes value based on temperature. The sensor has a negative-temperature coefficient. This means that as the temperature increases, the resistance decreases, and as the temperature decreases the resistance increases. The powertrain control module (PCM) supplies a 5-volt reference signal to the sensor on circuit 1227 and measures the voltage drop in the circuit. When the transmission fluid is cold, the sensor resistance is high and the PCM detects high signal voltage. As the fluid temperature warms to a normal operating temperature, the resistance becomes less and the signal voltage decreases. The PCM uses this information to control shift quality and torque converter clutch apply. DTC P0712 is a type D DTC.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The TFT sensor indicates a voltage less than 0.14 volts. |
| • | All conditions are met for 15 seconds. |
Action Taken When the DTC Sets
| • | The PCM does not illuminate the malfunction indicator lamp (MIL). |
| • | The PCM commands increased line pressure. |
| • | The PCM freezes shift adapts. |
| • | The PCM determines a TFT default transmission fluid temperature (TFT) using the following matrix: |
| - | If the engine run time is less than 60 seconds then default TFT equals the intake air temperature (IAT), plus 5 degrees. |
| - | If the engine coolant temperature (ECT) is less than 85°C (185°F) then default TFT equals IAT plus 10 degrees. |
| - | If the ECT is 85°-110°C (185°-230°F) then default TFT equals ECT plus 10 degrees. |
| - | If the ECT is greater 110°C (230°F) then default TFT is set to 140°C (284°F) and transmission shift pattern is in Hot Mode |
| - | If ECT and TFT DTCs are both set then default TFT is 140°C (284°F). |
| • | The PCM stores DTC P0712 in PCM history. |
Conditions for Clearing the DTC
| • | A scan tool clears the DTC from PCM history. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the wiring at the PCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Reduced terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change. |
| • | First diagnose and clear any engine DTCs or APP sensor DTCs that are present. Then inspect for any transmission DTCs that may have reset. |
| • | DTC P0218 may set approximately 600 seconds after DTC P0712 has set. Follow the diagnostic table for DTC P0712 before proceeding to the diagnostic table for DTC P0218. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground or a skewed sensor by verifying the fault still exists.
-
This step tests for an internal fault within the transmission by creating an open.
-
This step inspects circuit 1227 of the A/T wiring harness assembly for being shorted to ground.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
2 | Perform the Transmission Fluid Checking Procedure. Refer to Transmission Fluid Check . Was the Transmission Fluid Checking Procedure performed? | -- | Go to Transmission Fluid Check | |
Important: Before clearing the DTCs, use the scan tool in order to record the Failure Records. Using the Clear Info function erases Failure Records from the PCM. Does the scan tool display a TFT sensor voltage less than the specified value? | 0.13 volts | Go to Diagnostic Aids | ||
Does the scan tool display a TFT sensor voltage greater than the specified value? | 4.92 volts | |||
5 |
Refer to Electronic Component Description . Is the resistance within specified values? | 16,000ohms at 10°C (50°F) to 133ohms at 110°C (230°F) | ||
Measure the resistance between terminal L and a good ground on the transmission case. Is the resistance less than the specified value? | 50k ohms | Go to Diagnostic Aids | ||
7 |
Is the resistance less than the specified value? | 50k ohms | ||
8 | Replace the TFT sensor. Refer to A/T Fluid Temperature Sensor Replacement. Is the replacement complete? | -- | -- | |
9 | Inspect circuit 1227 (YEL/BLK) for a short to ground. Refer to General Electrical Diagnosis in Wiring Systems. Was the condition found? | -- | ||
10 | Replace the automatic transmission wiring harness assembly. Refer to Automatic Transmission Wiring Harness Replacement. Is the replacement complete? | -- | -- | |
11 | Inspect the PCM for faulty connections. Was the condition found? | -- | ||
12 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming in Engine Controls. Is the replacement complete? | -- | -- | |
13 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
