GM Service Manual Online
For 1990-2009 cars only

Removal Procedures


    Object Number: 104973  Size: SH
  1. Disconnect the battery negative cables from the batteries. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Remove the lower intake manifold from the cylinder head. Refer to Intake Manifold Replacement .
  3. Mark the fuel line retaining clips and the stud in order to ensure proper reinstallation.
  4. Important: Do not bend the fuel injector lines in order to ease in the removal of the valve rocker arm cover.

  5. Remove the fuel injection lines from the fuel nozzles.
  6. Remove the engine oil level indicator and tube from the engine block. Refer to Oil Level Indicator and Tube Replacement .
  7. Remove the transmission oil level indicator and tube.
  8. Remove the fuel return line clip at the valve rocker arm cover stud.

  9. Object Number: 105624  Size: SH
  10. Remove the rear generator support bracket.

  11. Object Number: 358437  Size: SH
  12. Remove the valve rocker arm cover bolts.

  13. Object Number: 358435  Size: SH

    Notice: Prying on the valve rocker arm cover may cause damage to the sealing surfaces. Use a block of wood against the side of the valve rocker arm cover and strike with a hammer in a sideways direction to shear the RTV sealant.

  14. Remove the valve rocker arm cover from the cylinder head.
  15. Clean the oil and grease from the sealing surfaces on the valve rocker arm and the cylinder head. Use a suitable solvent.

Installation Procedure

Notice: Do not allow the RTV sealant to enter any blind threaded hole. RTV sealant that is allowed to enter a blind threaded hole can cause hydraulic lock of the fastener when the fastener is tightened. Hydraulic lock of a fastener can lead to damage to the fastener and/or the components. Hydraulic lock of a fastener can also prevent the proper clamping loads to be obtained when the fastener is tightened. Improper clamping loads can prevent proper sealing of the components allowing leakage to occur. Preventing proper fastener tightening can allow the components to loosen or separate leading to extensive engine damage.


    Object Number: 606749  Size: SH
  1. Clean the sealing surface of the cylinder head.
  2. Clean the sealing surface of the valve rocker arm cover.
  3. Important: Apply a 5 to 8 N·m (3/16 to 5/16 inch) bead of RTV sealant to the valve rocker arm cover. The sealant should be applied such as that it follows and overlaps the stepped ridge. This will distribute the RTV on both the upper and lower levels of the step. When the valve rocker arm cover is fasten to the cylinder head, the RTV should flow on both the valve rocker arm cover and the cylinder head sealing surfaces. The sealer must be wet to the touch when the bolts are tighten to specifications.

  4. Apply the sealant GM P/N 12345739 to the valve rocker arm covers.

  5. Object Number: 358435  Size: SH
  6. Install the valve rocker arm cover to the cylinder head.
  7. Install the lower intake manifold to the cylinder head. Refer to Intake Manifold Replacement .

  8. Object Number: 358437  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  9. Install the valve rocker arm cover bolts.
  10. Tighten
    Tighten the bolts to 22 N·m (16 lb ft).

  11. Install the fuel injection lines and clips.
  12. Install the engine oil level indicator and tube. Refer to Oil Level Indicator and Tube Replacement .

  13. Object Number: 104973  Size: SH
  14. Install the transmission oil level indicator tube and bracket.

  15. Object Number: 105624  Size: SH
  16. Install the rear generator support bracket.
  17. Connect the battery negative cables from the batteries. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.