Circuit Description
The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high, and decreases the signal voltage as the engine runs leaner. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.
The HO2S contains a heater that is necessary in order to quickly warm the sensor to operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. It also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel control operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or "lean-out" the mixture, when the HO2S detects a rich exhaust condition.
Certain vehicle models utilize an oxygen sensor behind the catalytic converter in order to monitor catalyst efficiency.
This diagnostic trouble code (DTC) determines if the HO2S is functioning properly. It checks for an adequate number of HO2S voltage transitions above and below the bias range of 300-600 mV. This DTC sets when the vehicle control module (VCM) fails to detect a minimum number of voltage transitions above and below the bias range during the test period. Possible causes of this DTC are:
| • | An open or a short to voltage on either the HO2S signal or HO2S low circuits |
| • | A malfunctioning HO2S |
| • | A problem in the HO2S heater or its circuit |
| • | A faulty HO2S ground |
This DTC determines if the post-converter HO2S heater circuit is functioning properly by monitoring the amount of time required for the HO2S to reach operating temperature. This DTC sets when the VCM fails to detect HO2S voltage transitions above and below the bias range within a specified amount of time. Possible cause of this DTC are listed below.
| • | An open circuit in either the HO2S ignition feed or the HO2S heater ground circuits. |
| • | An HO2S heater element problem. |
Conditions for Running the DTC
Important: This test is void for this cold start if the system voltage remains outside the specified range for more than 4 seconds
| • | The system voltage is between 11.7-17 volts |
| • | The mass air flow (MAF) is less than 27 g/s |
| • | The engine run time is more than 2 seconds |
| • | The engine coolant temperature (ECT) is less than 33°C (91°F) |
| • | The intake air temperature (IAT) is less than 33°C (91°F) |
| • | The difference between the ECT and IAT is 5°C (9°F) or less |
Conditions for Setting the DTC
The O2 sensor voltage remains within 150 mV of the startup voltage for 245 seconds after cold start.
Action Taken When the DTC Sets
The VCM turns the MIL ON after 2 consecutive test failures.
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Important: Never solder the HO2S wires. For proper wire and connection repair refer to Wiring Repairs or Connector Repairs in Wiring Systems.
An intermittent may be caused by any of the following conditions:
| • | A poor connection |
| • | Rubbed through wire insulation |
| • | A broken wire inside the insulation |
Thoroughly inspect any circuitry that is suspected of causing the intermittent complaint. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
As the heater warms the oxygen sensor to operating temperature, the HO2S will output a voltage in relation to the amount of oxygen in the exhaust. With the ignition ON and the engine OFF the exhaust usually contains a high oxygen content. With the engine OFF the HO2S voltage will usually decrease from the initial bias voltage due to the high oxygen content.
-
This step checks for proper HO2S heater ignition feed and ground supply.
-
This step checks for proper VCM and signal circuit operation.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||||||||||
|
Important: The HO2S must be cool before proceeding with diagnosis. The ignition must remain OFF for at least one half hour before proceeding with diagnosis.
Does the HO2S voltage increase or decrease from the initial voltage by at least the specified value? | 150 mV | |||||||||||
3 |
Did you find a problem? | -- | Go to Diagnostic Aids | |||||||||
Does the test lamp illuminate? | -- | |||||||||||
Ensure the ignition is ON, while the engine is OFF. Is the voltage less than the specified value? | 20 mV | |||||||||||
6 | Connect the test lamp between the HO2S heater ignition feed circuit on the engine harness side and a known good ground. Ensure the ignition is ON, while the engine is OFF. Does the test lamp illuminate? | -- | ||||||||||
7 |
Is the resistance less than the specified value? | 5 ohms | ||||||||||
8 | Replace the HO2S. Refer to Heated Oxygen Sensor Replacement . Is the action complete? | -- | -- | |||||||||
9 | Repair the open HO2S heater ground circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
10 | Repair the lack of voltage on the HO2S heater ignition feed circuit. Refer to Wiring Repairs in Wiring Systems. If the fuse is open repair the short to ground on the circuit. An open fuse or a lack of voltage to the fuse may cause other DTCs or symptoms to be present. Is the action complete? | 5 ohms | -- | |||||||||
11 | Repair the circuit that measured high resistance. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
12 |
Did you find a problem? | -- | ||||||||||
13 |
Important: The replacement VCM must be programmed. Replace the VCM. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |||||||||
14 |
Important: The HO2S must be cool before proceeding with this diagnosis. The Ignition must remain OFF for at least one half hour before proceeding with the diagnosis.
Does the HO2S voltage increase or decrease from the initial voltage by at least the specified value? | 150 mV | ||||||||||
15 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the applicable DTC table | System OK |
