Fuel Tank Filler Hose Replacement Passenger/Cargo Van

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable.
2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnecting in order to avoid contamination of the fuel system.
3. Remove the fuel filler cap.
4. Drain the fuel below the level of the fuel tank fill hose. Refer to Fuel Tank Draining .
5. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
6. Loosen the fuel fill hose clamps (2).
7. Remove the fuel fill hose.
8. Cap the open end of the fuel tank.

1. Uncap the fuel tank.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the fuel fill hose.

Tighten
Tighten the fuel fill hose clamps (2) to 2.75 N·m (24 lb in).

3. Lower the vehicle.
4. Refill the fuel tank.
5. Install the fuel filler cap.
6. Connect the negative battery cable.

Fuel Tank Filler Hose Replacement Cutaway Van Rear Tank

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable.
2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnecting in order to avoid possible contamination of the fuel system.
3. Remove the fuel filler cap.
4. Drain the fuel below the level of the fuel tank fill hose. Refer to Fuel Tank Draining .
5. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
6. Loosen the fuel fill hose clamps (2).
7. Remove the fuel fill hose (3).
8. Cap the open end of the fuel tank.

1. Uncap the fuel tank.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the fuel fill hose (3).

Tighten
Tighten the fuel fill hose clamps (2) to 2.75 N·m (24 lb in).

3. Lower the vehicle.
4. Refill the fuel tank.
5. Install the fuel filler cap.
6. Connect the negative battery cable.

Fuel Tank Filler Hose Replacement Cutaway Van Side Tank

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

1. Disconnect the negative battery cable.
2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnecting in order to avoid possible contamination of the fuel system.
3. Remove the fuel filler cap.
4. Drain the fuel below the level of the fuel tank fill hose. Refer to Fuel Tank Draining .
5. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
6. Loosen the fuel fill hose clamps (2, 3).
7. Remove the fuel fill hose (6).
8. Cap the open end of the fuel tank.

1. Uncap the fuel tank.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the fuel fill hose (6).

Tighten
Tighten the fuel fill hose clamps (2, 3) to 2.75 N·m (24 lb in).

3. Lower the vehicle.
4. Refill the fuel tank.
5. Install the fuel filler cap.
6. Connect the negative battery cable.