Circuit Description
The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high. When the HO2S detects that the engine is operating lean, the signal voltage is low. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.
The HO2S contains a heater that is necessary in order to quickly warm the sensor to the operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. The control module also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel control operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or "lean out" the mixture, when the HO2S detects a rich exhaust condition.
This DTC is designed to detect an HO2S voltage that remains low for more than a specified number of seconds during the test conditions.
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0300, P0351, P0401, P0404, P0405, P0440, P0442, P0446, P0452, P0453, P1258, P1404, or P1441 are not set. |
| • | The air fuel ratio is between 14.5:1-14.7:1. |
| • | The throttle position (TP) sensor is between 3-70 percent. |
| • | The loop status is closed. |
| • | The ignition 1 signal is between 9-18 volts. |
| • | The fuel tank level remaining is more than 10 percent. |
| • | Intrusive tests are not in progress. |
| • | The scan tool output controls are not active. |
Conditions for Setting the DTC
The HO2S voltage is less than 26 mV for 750 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
Important: Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing or replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.
| • | Inspect the HO2S--The sensor pigtail may be in contact with the exhaust manifold or with the exhaust system. |
| • | Check the HO2S oxygen supply--An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provide the supply of oxygen. Inspect the HO2S wires and connections for breaks or contamination. Refer to Heated Oxygen Sensor Wiring Repairs in Wiring Systems. |
| • | Check for an intermittent ground in the signal wire between the connector and the sensor--Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the lean fuel injectors--Perform the Fuel Injector Balance Test. Refer to Fuel Injector Balance Test with Tech 2 , or refer to Fuel Injector Balance Test with Special Tool . |
| • | Check for fuel contamination--Water near the in-tank fuel pump inlet can be delivered to the injectors. The water causes a lean exhaust and can set a DTC. Refer to Fuel Injector Balance Test with Tech 2 . |
| • | Check the fuel pressure--The system will be lean if the fuel pressure is low. Refer to Fuel System Diagnosis . |
| • | Check for exhaust leaks--An exhaust leak near the HO2S can cause a lean condition. Refer to Exhaust Leakage in Engine Exhaust. |
| • | Check for vacuum leaks or for crankcase leaks that can cause a lean condition. |
| • | If the components listed above are OK, the HO2S may be at fault. |
For an intermittent condition, refer to Symptoms - Engine Controls .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
If the voltage is below the specified value the condition is present.
-
Jumpering the HO2S low signal circuit to ground is necessary for the PCM to correctly measure the voltage on the HO2S high signal circuit. If the HO2S voltage is within the specified range, the PCM and HO2S high signal circuit are OK.
Step | Action | Value(s) | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||||||
|
Important: With the engine running, observe the front HO2S voltage using a scan tool. If the front HO2S voltage is fixed above 900 mV, refer to DTC P0132 or P0152 .
Is the HO2S voltage less than the specified value? | 26 mV | Go to Step 4 | Go to Step 3 | |||||||||||||
3 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids | ||||||||||||
Is the HO2S voltage within the specified range? | 350-550 mV | Go to Step 5 | Go to Step 6 | |||||||||||||
5 |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 8 | ||||||||||||
6 |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 7 | ||||||||||||
7 | Test the HO2S high signal circuit for a short to the HO2S Low signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||||||||
8 | Inspect for poor connections at the harness connector of the HO2S. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | ||||||||||||
9 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 | ||||||||||||
10 | Replace the affected HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||||||
11 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||||||
12 |
Does the DTC run and pass? | -- | Go to Step 13 | Go to Step 2 | ||||||||||||
13 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |||||||||||||
