GM Service Manual Online
For 1990-2009 cars only

Step

Action

Yes

No

Schematic Reference: Starting and Charging Schematics

1

Did you perform the Engine Electrical Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Engine Electrical

2

Turn the ignition switch to the START position.

Does the engine crank?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

Turn the ignition switch to the START position.

Does the starter motor relay click?

Go to Step 11

Go to Step 4

4

Is the vehicle equipped with a manual transmission?

Go to Step 5

Go to Step 7

5

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Clutch Start Switch Signal parameter in the PCM data list while pressing the clutch pedal.

Does the scan tool display Released/Applied?

Go to Step 7

Go to Step 6

6

  1. Turn OFF the ignition.
  2. Disconnect the PCM harness connector.
  3. Connect a test lamp between the Clutch Start Switch Signal of the PCM harness and a good ground.
  4. Turn the ignition to the START position while pressing the clutch pedal.

Does the test lamp illuminate?

Go to Step 7

Go to Step 8

7

  1. Turn OFF the ignition.
  2. Disconnect the PCM harness connector.
  3. Connect a test lamp between the crank voltage circuit (starter enable relay control) of the PCM harness and a good ground.
  4. Turn the ignition to the START position.

Does the test lamp illuminate?

Go to Step 19

Go to Step 8

8

  1. Remove the starter motor relay.
  2. Connect a test light from the supply voltage circuit of the starter motor relay coil circuit to ground.
  3. With the transmission in park, or clutch pedal pressed, turn the ignition switch to the START position.

Does the test light illuminate?

Go to Step 9

Go to Step 10

9

  1. Connect a test light from the supply voltage circuit of the starter motor relay coil circuit to the control circuit of the starter motor relay coil circuit.
  2. With the transmission in park, or clutch pedal pressed, turn the ignition switch to the START position.

Does the test light illuminate?

Go to Step 17

Go to Step 14

10

  1. Turn OFF the ignition.
  2. Disconnect the park neutral position (PNP) switch. Refer to Park/Neutral Position Switch Replacement in Automatic Transmission-4L60-E or Park/Neutral Position Switch Replacement in Automatic Transmission-4L80-E.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a 10-amp fused jumper between the starter motor relay coil control circuits of the PNP switch.
  5. With the transmission in PARK, turn the ignition switch to the START position.

Does the test lamp illuminate?

Go to Step 18

Go to Step 15

11

  1. Turn OFF the ignition.
  2. Disconnect the starter motor relay.
  3. Connect a test lamp between the battery positive voltage circuit of the starter motor relay switch circuit and a good ground.

Does the test lamp illuminate?

Go to Step 12

Go to Step 23

12

Connect a 30-amp fused jumper between the battery positive voltage circuit of the starter motor relay switch circuit and the supply voltage circuit of the starter solenoid.

Does the engine crank?

Go to Step 17

Go to Step 13

13

Does the fuse in the jumper open?

Go to Step 24

Go to Step 16

14

Test the control circuit of the starter motor relay for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 25

15

Test the supply voltage circuit of the starter motor relay coil circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 21

16

Test the supply voltage circuit of the starter solenoid for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 22

17

Inspect for poor connections at the starter motor relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 25

18

    • If equipped with an automatic transmission, inspect for poor connection at the PNP switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. If OK, perform the Park/Neutral Position Switch Adjustment in Automatic Transmission-4L60-E or Park/Neutral Position Switch Adjustment in Automatic Transmission-4L80-E.
    • If equipped with a manual transmission, inspect for poor connection at the clutch pedal position switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 26

19

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 20

20

Important: The replacement PCM must be programmed.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.

Is action complete?

Go to Step 29

--

21

Inspect for poor connections at the ignition switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 27

22

Inspect for poor connections at the starter solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 28

23

Repair the open or high resistance in the battery positive voltage circuit of the starter motor relay switch circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 29

--

24

Repair the short to ground in the supply voltage circuit of the starter solenoid. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 29

--

25

Replace the starter relay. Refer to Relay Replacement in Wiring Systems.

Did you complete the replacement?

Go to Step 29

--

26

Replace the PNP switch. Refer to Park/Neutral Position Switch Replacement in Automatic Transmission-4L60-E or Park/Neutral Position Switch Replacement in Automatic Transmission-4L80-E.

Did you complete the replacement?

Go to Step 29

--

27

Replace the ignition switch. Refer to Ignition and Start Switch Replacement in Steering Wheel and Column.

Did you complete the replacement?

Go to Step 29

--

28

Replace the starter. Refer to Starter Motor Replacement .

Did you complete the replacement?

Go to Step 29

--

29

Operate the system for which the symptom occurred.

Did you correct the condition?

System OK

Go to Step 2