The brake switch informs the electronic brake control module (EBCM) when the brake is depressed. The brake switch is normally closed, supplying 12 volts to the EBCM when the brake is released. When the brake pedal is pressed, voltage on the torque converter clutch (TCC) brake switch signal circuit is 0 volts.
This diagnostic procedure supports the following DTC:
DTC C0161 Antilock Brake System (ABS)/Traction Control System (TCS) Brake Switch Circuit
Any of the following conditions may cause the DTC to run:
• | The vehicle accelerates from 0 km/h (0 mph) to a speed greater than 56 km/h (35 mph). |
• | The vehicle experiences an ABS event involving all hydraulic circuits. |
Any of the following conditions may cause the DTC to set:
• | Voltage on the TCC brake switch signal circuit is always low. |
• | Voltage on the TCC brake switch signal circuit is always high. |
The EBCM stores this information-only DTC for as long as the condition is present:
The Conditions for Setting the DTC are no longer present and you use the scan tool Clear DTCs function.
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to Testing for Intermittent Conditions and Poor Connections , Connector Repairs , Testing for Electrical Intermittents , and Wiring Repairs .
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Does the scan tool display Off? | Go to Step 3 | Go to Step 5 |
3 |
Does the scan tool display On? | Go to Diagnostic Aids | Go to Step 4 |
Does the scan tool display On? | Go to Step 9 | Go to Step 7 | |
Does the scan tool display Off? | Go to Step 9 | Go to Step 6 | |
6 | Test the ignition 3 voltage circuit and the TCC brake switch signal circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
7 | Test the TCC brake switch signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
8 | Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
10 |
Important: Following EBCM replacement, use the scan tool to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Control Module References . Did you complete the replacement? | Go to Step 12 | -- |
11 | Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement . Did you complete the replacement? | Go to Step 12 | -- |
12 |
Does the DTC reset? | Go to Step 2 | System OK |
The brake switch informs the electronic brake control module (EBCM) when the brake is depressed. The brake switch is normally closed, supplying 12 volts to the EBCM when the brake is released. When the brake pedal is pressed, voltage on the torque converter clutch (TCC) brake switch signal circuit is 0 volts.
This diagnostic procedure supports the following DTC:
DTC C0161 Antilock Brake System (ABS)/Traction Control System (TCS) Brake Switch Circuit
Any of the following conditions may cause the DTC to run:
• | The vehicle accelerates from 0 km/h (0 mph) to a speed greater than 56 km/h (35 mph). |
• | The vehicle experiences an ABS event involving all hydraulic circuits. |
• | The EBCM detects that the master cylinder pressure is greater than 1 400 kPa (200 psi) and that the vehicle is decelerating. |
Any of the following conditions may cause the DTC to set:
• | Voltage on the TCC brake switch signal circuit is always low. |
• | Voltage on the TCC brake switch signal circuit is always high. |
• | Voltage on the TCC brake switch signal circuit is high for 0.5-4 seconds when voltage is expected to be low. |
• | The EBCM disables the vehicle stability enhancement system (VSES). |
• | The TCS operates with engine torque reduction capability only. |
• | The stability indicator turns ON. |
The Conditions for Setting the DTC are no longer present and you use the scan tool Clear DTCs function.
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to Testing for Intermittent Conditions and Poor Connections , Connector Repairs , Testing for Electrical Intermittents , and Wiring Repairs .
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Lighting Systems Connector End Views or Antilock Brake System Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Does the scan tool display Off? | Go to Step 3 | Go to Step 5 |
3 |
Does the scan tool display On? | Go to Diagnostic Aids | Go to Step 4 |
Does the scan tool display On? | Go to Step 9 | Go to Step 7 | |
Does the scan tool display Off? | Go to Step 9 | Go to Step 6 | |
6 | Test the ignition 3 voltage circuit and the TCC brake switch signal circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
7 | Test the TCC brake switch signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
8 | Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
10 |
Important: Following EBCM replacement, perform the set-up procedure for the EBCM and perform the Yaw Rate Reference Table Reset Procedure. Use the scan tool to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Control Module References . Did you complete the replacement? | Go to Step 12 | -- |
11 | Replace the stop lamp switch. Refer to Stop Lamp Switch Replacement . Did you complete the replacement? | Go to Step 12 | -- |
12 |
Does the DTC reset? | Go to Step 2 | System OK |