GM Service Manual Online
For 1990-2009 cars only

Exhaust Manifold Replacement - Right Side 4.8L, 5.3L, and 6.0L Engines


    Object Number: 858553  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the exhaust manifold pipe nuts.
  3. Lower the vehicle.
  4. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .
  5. Remove the spark plugs. Refer to Spark Plug Replacement .

  6. Object Number: 858557  Size: SH
  7. Remove the exhaust manifold bolts, manifold, and gasket.
  8. Discard the gasket.

  9. Object Number: 492768  Size: SH
  10. Remove the heat shield bolts (1), and shield (2) from the exhaust manifold (1), if necessary.
  11. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection .

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 492768  Size: SH
  1. Install the heat shield (2), and bolts (1) to the exhaust manifold (1), if necessary.
  2. Tighten
    Tighten the bolts to 9 N·m (80 lb in).


    Object Number: 858557  Size: SH

    Important: 

       • Tighten the exhaust manifold bolts as specified in the service procedure. Improperly installed and/or leaking exhaust manifold gaskets may affect vehicle emissions and/or On-Board Diagnostics (OBD) II system performance.
       • The cylinder head exhaust manifold bolt hole threads must be clean and free of debris or threadlocking material.

    Important: Do not apply sealant to the first three threads of the bolt.

  3. Apply a 5 mm (0.2 in) wide band of threadlock GM P/N 12345493 (Canadian P/N 10953488), or equivalent to the threads of the exhaust manifold bolts.
  4. Install the exhaust manifold, NEW gasket and bolts.
  5. Tighten

    1. Tighten the bolts a first pass to 15 N·m (11 lb ft). Tighten the bolts beginning with the center 2 bolts. Alternate from side-to-side, and work toward the outside bolts.
    2. Tighten the bolts a final pass to 25 N·m (18 lb ft). Tighten the bolts beginning with the center 2 bolts. Alternate from side-to-side, and work toward the outside bolts.
  6. Using a flat punch, bend over the exposed edge of the exhaust manifold gasket at the front of the right cylinder head.
  7. Install the spark plugs. Refer to Spark Plug Replacement .
  8. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .
  9. Raise the vehicle.

  10. Object Number: 858553  Size: SH
  11. Install the exhaust manifold pipe nuts.
  12. Tighten
    Tighten the nuts to 50 N·m (37 lb ft).

  13. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 4.3L Engine

Removal Procedure


    Object Number: 858553  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the right exhaust manifold pipe nuts.
  3. Lower the vehicle.

  4. Object Number: 360851  Size: SH
  5. Loosen the air cleaner outlet duct clamp at the mass airflow (MAF)/intake air temperature (IAT) sensor.

  6. Object Number: 701705  Size: SH
  7. Remove the positive crankcase ventilation (PCV) hose.

  8. Object Number: 489179  Size: SH
  9. Remove the air cleaner adapter nut.

  10. Object Number: 489176  Size: SH
  11. In order to remove the air cleaner outlet duct, pivot the duct upward until the hinge clip releases from the lip on the throttle body.
  12. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .

  13. Object Number: 14824  Size: SH
  14. Disconnect the spark plug wires from the spark plugs.
  15. Remove the spark plug wire retainer bolt.
  16. Reposition the wire retainer to the top of the engine.
  17. Remove the spark plugs.

  18. Object Number: 188121  Size: SH
  19. Remove the exhaust manifold and spark plug heat shield bolts.
  20. Remove the exhaust manifold and spark plug heat shields.

  21. Object Number: 328555  Size: SH
  22. Remove and discard the exhaust manifold gaskets.

  23. Object Number: 493851  Size: SH
  24. Remove the exhaust manifold heat shield, if required.
  25. Clean all gasket mating surfaces.

Installation Procedure


    Object Number: 493851  Size: SH
  1. Install the exhaust manifold heat shield, if required.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the exhaust manifold heat shield bolts.
  4. Tighten
    Tighten the bolts to 9 N·m (80 lb in).


    Object Number: 476818  Size: SH

    Important: To assist in installing the exhaust manifold and gasket to the engine, tabs on a NEW exhaust manifold gasket will hold the gasket and bolts in place.

  5. Install NEW exhaust manifold gaskets to the exhaust manifold.
  6. Ensure that the exhaust manifold bolts, and plug wire shields are held in place by the tabs on the exhaust manifold gaskets.

  7. Object Number: 188121  Size: SH
  8. Install the exhaust manifold and plug wire shields.
  9. If reusing the old fasteners, apply threadlock GM P/N 12345493, (Canadian P/N 10953488), or equivalent to the threads of the exhaust manifold bolts.
  10. Install the exhaust manifold bolts.
  11. Tighten
    Tighten the bolts to 30 N·m (22 lb ft).


    Object Number: 14824  Size: SH
  12. Install the spark plugs.
  13. Position the spark plug wire retainer to the engine.
  14. Loosely install the spark plug wire retainer bolt.
  15. Connect the spark plug wires to the spark plugs.
  16. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .
  17. Tighten the spark plug wire retainer bolt.
  18. Tighten
    Tighten the bolt to 12 N·m (106 lb in).


    Object Number: 489176  Size: SH
  19. Align the hinge clip with the lip on the throttle body.
  20. In order to install the air cleaner outlet duct, pivot the air cleaner outlet duct downward until the mounting stud is through the hole.


    Object Number: 489179  Size: SH
  21. Install the air cleaner adapter nut.

  22. Object Number: 701705  Size: SH
  23. Install the PCV hose.

  24. Object Number: 360851  Size: SH
  25. Tighten the air cleaner outlet duct clamp at the MAF/IAT sensor.
  26. Raise the vehicle.

  27. Object Number: 858553  Size: SH
  28. Install the right exhaust manifold pipe nuts.
  29. Tighten
    Tighten the nuts to 50 N·m (37 lb ft).

  30. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 6.6L Engine

Removal Procedure


    Object Number: 1336106  Size: SH
  1. Raise the vehicle enough in order to work through the wheelhouse opening. Refer to Lifting and Jacking the Vehicle .
  2. Remove the wheelhouse panel. Refer to Wheelhouse Panel Replacement .
  3. Remove the exhaust manifold heat shield bolts.
  4. Remove the exhaust manifold heat shield.

  5. Object Number: 1334834  Size: SH
  6. Remove the right exhaust pipe to the exhaust manifold bolts (3, 4, and 5).

  7. Object Number: 1336107  Size: SH
  8. Remove the exhaust manifold bolts and nuts in the proper sequence.

  9. Object Number: 1336108  Size: SH
  10. Remove the exhaust manifold.
  11. Remove the bolt for the oil level indicator tube bracket in order to remove the exhaust manifold gasket.
  12. Remove and discard the exhaust manifold gasket.
  13. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection .

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1336108  Size: SH
  1. Install the exhaust manifold gasket to the cylinder head.
  2. Install the bolt for the oil level indicator tube bracket.
  3. Tighten
    Tighten the bolt to 21 N·m (15 lb ft).

  4. Install the exhaust manifold.
  5. Install the exhaust manifold bolts/nuts.

  6. Object Number: 1336107  Size: SH
  7. Using the sequence shown, properly tighten the exhaust manifold bolts.
  8. Tighten
    Tighten the bolt/nuts to 38 N·m (28 lb ft).


    Object Number: 1336106  Size: SH
  9. Install the exhaust manifold heat shield.
  10. Install the exhaust manifold heat shield bolts.
  11. Tighten
    Tighten the bolts to 8 N·m (71 lb in).


    Object Number: 1334834  Size: SH
  12. Install the exhaust pipe gasket. Align the tab on the gasket to face outward.
  13. Install the exhaust pipe bolts (3, 4, and 5).
  14. Tighten
    Tighten the bolts to 53 N·m (39 lb ft).

  15. Install the wheelhouse panel. Refer to Wheelhouse Panel Replacement .
  16. Lower the vehicle.

Exhaust Manifold Replacement - Right Side 8.1L Engine

Removal Procedure


    Object Number: 470704  Size: SH
  1. Remove the wheelhouse panel. Refer to Wheelhouse Panel Replacement .
  2. Remove the oil level indicator. Refer to Oil Level Indicator and Tube Replacement .
  3. Important: Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug or the wire could be damaged.

  4. Remove the spark plug wires from the spark plugs and ignition coils.
  5. Remove the spark plugs. Refer to Spark Plug Replacement .
  6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .

  7. Object Number: 858564  Size: SH
  8. Remove the exhaust manifold heat shield bolts and nuts.
  9. Remove the exhaust manifold heat shield.
  10. Lower the vehicle.

  11. Object Number: 470719  Size: SH
  12. Remove the exhaust manifold bolt and nuts.
  13. Remove the exhaust manifold.
  14. Remove and discard the exhaust manifold gasket.
  15. Clean and inspect the exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection .

Installation Procedure


    Object Number: 470719  Size: SH
  1. Install the a NEW exhaust manifold gasket.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the exhaust manifold.
  4. Install the exhaust manifold bolt and nuts.
  5. Tighten

        • Tighten the bolt to 35 N·m (26 lb ft).
        • Tighten the nuts to 16 N·m (12 lb ft).
  6. Raise and suitably support the vehicle with safety stands.

  7. Object Number: 858564  Size: SH
  8. Install the exhaust manifold heat shield.
  9. Install the exhaust manifold heat shield bolts and nuts.
  10. Tighten
    Tighten the bolts/nuts to 25 N·m (18 lb ft).

  11. Lower the vehicle.
  12. Install the spark plugs. Refer to Spark Plug Replacement .

  13. Object Number: 470704  Size: SH

    Important: Fully install the spark plug wires by pushing on the exposed end of the spark plug boot. Do not push the spark plug wire on to the spark plug by using the metal heat shield.

  14. Install the spark plug wires to the spark plugs and ignition coils.
  15. Install the oil level indicator. Refer to Oil Level Indicator and Tube Replacement .
  16. Install the wheelhouse panel. Refer to Wheelhouse Panel Replacement .