The driver and passenger seat heaters are controlled by the driver seat module (DSM). Power is supplied to the driver seat cushion and back heater elements through individual voltage supply circuits. Power is supplied to the passenger seat cushion and back heater elements through a common voltage supply circuit. All of the driver and passenger seat heater elements are grounded by the DSM through individual low side drive control circuits. The heater element control circuits are pulse width modulated to ground by the DSM in order to control the seat temperatures by regulating the current flow through the heater elements.
This diagnostic procedure supports the following DTCs:
• | DTC B2425 Driver Seat Heater Circuit |
• | DTC B2430 Passenger Seat Heater Circuit |
The system voltage must be between 9-16 volts.
The DSM determines by monitoring the heater element control circuits that a short to voltage, short to ground, or open condition exists.
• | The heated seat with a current status DTC will be disabled. |
• | Both heated seats may be disabled. |
• | When the fault is no longer present a history status DTC will be stored, and heated seat operation will be restored. |
• | The DTC will be current for as long as the fault is present. |
• | When the fault is no longer present the DTC will be a history status code. |
• | The history DTC will be cleared after 100 error free ignition cycles, or by using the scan tool clearing DTCs feature. |
Step | Action | Values | Yes | No |
---|---|---|---|---|
Schematic Reference: Driver Seat Schematics and Passenger Seat Schematics Connector End View Reference: Power Seat Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 | Verify the condition is present. Does the system operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 |
3 |
Is voltage present on either of the heater element control circuits? | -- | Go to Step 7 | Go to Step 4 |
4 | Using a DMM test for continuity to ground at the heater element control circuit terminals in the DSM harness connector. Refer to Circuit Testing. Is continuity to ground present on either of the heater element control circuits? | -- | Go to Step 8 | Go to Step 5 |
5 | Using a DMM measure the resistance through the seat heater elements from the voltage supply circuit terminal to each of the control circuit terminals in the DSM harness connector. Refer to Circuit Testing. Are the measurements within the specified values? | 1.5-5.5 ohms | Go to Step 10 | Go to Step 6 |
6 | Test the voltage supply and control circuits to the affected heater element for an open or high resistance. Refer to Circuit Testing and to Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Repair the voltage supply or control circuit to the affected heater element for a short to voltage. Refer to Circuit Testingand to Wiring Repairs. Is the repair complete? | -- | Go to Step 13 | -- |
8 | Repair the voltage supply or control circuit to the affected heater element for a short to ground. Refer to Circuit Testingand to Wiring Repairs. Is the repair complete? | -- | Go to Step 13 | -- |
9 | Inspect for poor connections at the heater element connectors. Refer to Testing for Intermittent Conditions and Poor Connections and to Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
10 | Inspect for poor connections at the DSM connectors. Refer to Testing for Intermittent Conditions and Poor Connections and to Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
11 | Replace the affected seat heater element. Refer to Driver or Passenger Seat Back Cushion Heater Replacement and to Driver or Passenger Seat Cushion Heater Replacement . Is the repair complete? | -- | Go to Step 13 | -- |
12 | Replace the DSM. Refer to Control Module References for replacement, setup, and programming. Is the repair complete? | -- | Go to Step 13 | -- |
13 |
Does the DTC reset? | -- | Go to Step 3 | System OK |