GM Service Manual Online
For 1990-2009 cars only

Auxiliary Battery Positive Cable Replacement 6.2L

Removal Procedure


    Object Number: 1702793  Size: SH
  1. Disconnect the auxiliary battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the underhood junction block cover.

  3. Object Number: 1702795  Size: SH
  4. Lift the junction block retainers from the locked position (3) and rotate the retainers to the open position (1).
  5. Remove the junction block.

  6. Object Number: 1702797  Size: SH
  7. Remove the auxiliary battery positive cable connector (1) from the underhood bussed electrical center (UBEC).

  8. Object Number: 1857176  Size: SH
  9. Remove the mega fuse cover (3).
  10. Disconnect the auxiliary battery positive cable electrical connector (2) from the engine wiring harness connector.
  11. Remove the relay (1) clip from the stud on the front of dash.

  12. Object Number: 1857184  Size: SH
  13. Remove the auxiliary battery positive cable nut (1) from the mega fuse holder.
  14. Remove the generator battery jumper cable nut (3) from the mega fuse holder.
  15. Remove the generator battery jumper cable terminal (2) from the mega fuse stud.
  16. Remove the auxiliary battery positive cable from the mega fuse holder.

  17. Object Number: 1857177  Size: SH
  18. Disconnect auxiliary battery positive cable electrical connector (1) from the auxiliary battery relay.
  19. Reposition the auxiliary battery positive cable boot (5).
  20. Remove the auxiliary battery positive cable nut (4) and cable from the battery relay.
  21. Remove the auxiliary battery positive cable retainer (2) from the stud on the front of dash.
  22. Remove the auxiliary battery positive cable push nuts (6).

  23. Object Number: 1857381  Size: SH
  24. Remove the auxiliary battery positive cable from the vehicle.

Installation Procedure


    Object Number: 1857381  Size: SH
  1. Install the auxiliary battery positive cable to the vehicle.

  2. Object Number: 1857177  Size: SH
  3. Install the auxiliary battery positive cable push nuts (6).
  4. Install the auxiliary battery positive cable retainer (2) to the stud on the front of dash.
  5. Notice: Refer to Fastener Notice in the Preface section.

  6. Install the auxiliary battery positive cable and nut (4) to the battery relay.
  7. Tighten
    Tighten the nut to 9 N·m (80 lb in).

  8. Position the auxiliary battery positive cable boot (5).
  9. Connect auxiliary battery positive cable electrical connector (1) to the auxiliary battery relay.

  10. Object Number: 1857184  Size: SH
  11. Install the auxiliary battery positive cable to the mega fuse holder.
  12. Install the generator battery jumper cable terminal (2) to the mega fuse stud.
  13. Install the generator battery jumper cable nut (3) to the mega fuse holder.
  14. Tighten
    Tighten the nut to 9 N·m (80 lb in).

  15. Install the auxiliary battery positive cable nut (1) to the mega fuse holder.
  16. Tighten
    Tighten the nut to 9 N·m (80 lb in).


    Object Number: 1857176  Size: SH
  17. Connect the auxiliary battery positive cable electrical connector (2) to the engine wiring harness connector.
  18. Install the relay (1) clip to the stud on the front of dash.
  19. Install the mega fuse cover (3).

  20. Object Number: 1702797  Size: SH
  21. Install the auxiliary battery positive cable connector (1) to the UBEC.

  22. Object Number: 1702795  Size: SH
  23. Ensure that the junction block retainers are in the open position (1).
  24. Position and align the junction block to the 4 bracket pivots (2), once the pivots are engaged, push the retainers down into the locked position (3).

  25. Object Number: 1702793  Size: SH
  26. Install the underhood junction block cover.
  27. Connect the auxiliary battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .