Callout
| Component Name
|
Caution: Refer to Brake Fluid Irritant Caution in the Preface section.
Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.
Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM
with the ignition switch in the OFF position. Failure to observe this precaution
could result in damage to the EBCM/EBTCM.
Preliminary Procedures
- Turn the ignition switch to the OFF position.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove any dirt and debris from the area of the brake pressure modulator valve (BPMV) assembly.
- Disconnect the electronic brake control module (EBCM) electrical connector.
|
1
| Master Cylinder Inlet Brake Pipe Fitting (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
2
| Front Wheel Outlet Brake Pipe Fitting (Qty: 2)
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
3
| Rear Wheel Outlet Brake Pipe Fitting (Qty: 2)
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
4
| Brake Pressure Modulator Valve (BPMV) Bracket Bolt (Qty: 3)
Tip It is not necessary to remove the bolts; loosen the bolts and slide the BPMV and bracket assembly toward the front of the vehicle to remove.
Tighten 22 N·m (16 lb ft) |
5
| BPMV Mounting Nut (Qty: 2)
ProcedureIf removing the BPMV bracket from the BPMV, only loosen the mounting nuts.
Tighten 9 N·m (80 lb in) |
6
| BPMV Mounting Bracket
|
7
| BPMV Assembly
Procedure
- If necessary, remove the EBCM from the BPMV. Refer to
Electronic Brake Control Module Replacement
.
- Carefully lift the BPMV upward and release the BPMV from the lower grommet. DO NOT pry on the underside of the BPMV.
- Bleed the BPMV. Refer to
Antilock Brake System Automated Bleed Procedure
.
- Calibrate the brake pressure sensor. Refer to
Electronic Brake Control Module Programming and Setup
.
|
Callout
| Component Name
|
Caution: Refer to Brake Fluid Irritant Caution in the Preface section.
Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.
Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM
with the ignition switch in the OFF position. Failure to observe this precaution
could result in damage to the EBCM/EBTCM.
Preliminary Procedures
- Turn the ignition switch to the OFF position.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove any dirt and debris from the area of the brake pressure modulator valve (BPMV) assembly.
- Disconnect the electronic brake control module (EBCM) electrical connector.
|
1
| Master Cylinder Inlet Brake Pipe Fitting (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
2
| Front Wheel Outlet Brake Pipe Fitting (Qty: 2)
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
3
| Rear Wheel Outlet Brake Pipe Fitting
Tip Cap the brake pipe fittings to prevent brake fluid loss and contamination.
Tighten 18 N·m (13 lb ft) |
4
| Brake Pressure Modulator Valve (BPMV) Bracket Bolt (Qty: 3)
Tighten 22 N·m (16 lb ft) |
5
| BPMV Mounting Bolt
Tighten 11 N·m (97 lb in) |
6
| BPMV Mounting Bracket
ProcedureInspect the BPMV mounting bracket grommet for damage and replace, if necessary.
|
7
| BPMV Insulator (Qty: 2)
ProcedureInspect the BPMV insulators for damage and replace, if necessary.
|
8
| BPMV Assembly
Procedure
- If necessary, remove the EBCM from the BPMV. Refer to
Electronic Brake Control Module Replacement
.
- Bleed the antilock brake system. Refer to
Antilock Brake System Automated Bleed Procedure
.
- Calibrate the brake pressure sensor. Refer to
Electronic Brake Control Module Programming and Setup
.
|