GM Service Manual Online
For 1990-2009 cars only

Door Body Side Molding Replacement Chevrolet


Object Number: 1669888  Size: SF

Callout

Component Name

1

Front Side Door Molding

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Using a J 25070 Heat Gun in a circular motion, warm the front side door molding prior to removal. Carefully clean the body panel thoroughly prior to bonding the new front body side molding to the door.
  3. Ensure the front door is in the closed position prior to installing the new front side door molding.
  4. Remove the protective liner from the backside of the molding adhesive tape.
  5. Position the pin on the backside of the molding to the round hole at the rear edge of the front door first, then to the oval hole at the front edge of the door.
  6. Ensure full adhesion of the molding to the door using the palm of the hand with a clean dry towel working from the rear edge of the door to the front, down the entire molding.

Door Body Side Molding Replacement GMC


Object Number: 1839469  Size: SF

Callout

Component Name

1

Rear Side Door Molding

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Using a J 25070 Heat Gun in a circular motion, warm the front side door molding prior to removal. Carefully clean the body panel thoroughly prior to bonding the new front body side molding to the door.
  3. Ensure the rear door is in the closed position prior to installing the new rear side door moldings.
  4. Remove the protective liner from the backside of the molding adhesive tape.
  5. Position the pin on the backside of the molding to the round hole at the front edge of the rear door first, then to the oval hole at the rear edge of the door.
  6. Ensure full adhesion of the molding to the door using the palm of the hand with a clean dry towel working from the rear edge of the door to the front, down the entire molding.

Door Body Side Molding Replacement Crew Cab


Object Number: 1866420  Size: SF

Callout

Component Name

1

Front Side Door Molding

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Using a J 25070 Heat Gun in a circular motion, warm the front side door molding prior to removal. Carefully clean the body panel thoroughly prior to bonding the new front body side molding to the door.
  3. Ensure the front door is in the closed position prior to installing the new front side door moldings.
  4. Remove the protective liner from the backside of the molding adhesive tape.
  5. Position the pin on the backside of the molding to the round hole at the front edge of the front door first, then to the oval hole at the rear edge of the door.
  6. Ensure full adhesion of the molding to the door using the palm of the hand with a clean dry towel working from the rear edge of the door to the front, down the entire molding.

Door Body Side Molding Replacement Extended Cab


Object Number: 1866419  Size: SF

Callout

Component Name

1

Extended Door Side Molding

Procedure

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Using a J 25070 Heat Gun in a circular motion, warm the side door molding prior to removal. Carefully clean the body panel thoroughly prior to bonding the new door body side molding to the door.
  3. Ensure the door is in the closed position prior to installing the new side door moldings.
  4. Remove the protective liner from the backside of the molding adhesive tape.
  5. Position the molding to the edge of the side door, then to the rear edge of the door.
  6. Ensure full adhesion of the molding to the door using the palm of the hand with a clean dry towel working from the front edge of the door to the rear, down the entire molding.