DTC B0081 Non-Hybrid
Diagnostic Instructions
DTC Descriptors
DTC B0081 0F: Passenger Presence System Erratic
DTC B0081 3A: Passenger Presence System Incorrect Component Installed
DTC B0081 4B: Passenger Presence System Calibration Not Learned
DTC B0081 5A: Passenger Presence System Plausibility Failure
DTC B0081 39: Passenger Presence System Internal Electronic Failure
DTC B0081 71: Passenger Presence System Invalid Serial Data Received
Circuit/System Description
When the ignition is turned ON, the passenger presence system (PPS) and the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions. When the SDM has completed the power-up mode, the SDM will establish
communication with the PPS. The SDM will also request the instrument panel cluster (IPC) to illuminate both of the PASSENGER AIR BAG ON/OFF indicators ON for 5 seconds. If the SDM determines the correct PPS is installed and functioning normally, the SDM
will illuminate the passenger side airbags ON or OFF based on messages from the PPS. The SDM will also send a message to the IPC to illuminate the appropriate PASSENGER AIR BAG ON/OFF indicator.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
All of the following conditions must exist for 5 seconds:
B0081 0F
The SDM has received a fault present message from the PPS.
B0081 3A
The SDM has received a message from the PPS which indicates a vehicle and PPS mismatch.
B0081 4B
The PPS has failed the rezeroing procedure. Calibration not learned.
B0081 5A
| • | The PPS has lost communications with the SDM. |
| • | When the enabled state between the PPS and the SDM does not match. |
| • | The SDM signal stating the Passenger Status Data Received is not valid within 2.6 seconds after the PPS changes occupant classification. |
B0081 39
The SDM has received a critical malfunction message from the PPS.
B0081 71
The SDM has received invalid or no serial data from the PPS.
Action Taken When the DTC Sets
| • | The PPS will set a DTC, and then communicate with the SDM. |
| • | The SDM disables the Passenger Airbag Module. |
| • | The PPS will illuminate the Passenger Airbag status OFF indicator. |
| • | The SDM requests the instrument panel cluster (IPC) to illuminate the AIRBAG indicator. |
Conditions for Clearing the DTC
| • | The condition for setting the DTC no longer exists and there is no activity on the low speed serial data circuits. |
| • | A history DTC will clear once 250 malfunction-free ignition cycles have occurred. |
Diagnostic Aids
If either the SDM or PPS were replaced, verify that the correct part numbers were used for the vehicle application.
Reference Information
Schematic Reference
SIR Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
SIR System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Important:
| • | When removing connectors inspect for damage, corrosion or poor connection. Damage or corrosion in the following requires repair or replacement of the affected component/connector. |
| • | PPS module harness connector |
| • | SDM wiring harness connector |
- Ignition ON, verify no PPS DTCs are set in the PPS or SDM.
- Verify DTC B1000, B1001, or U0170 is not set as current.
- Verify DTC B0081 3A is not set as current.
| ⇒ | If DTC B0081 3A is set as current, replace the PPS with the correct part number. |
- Verify DTC B0081 5A is not set as current.
| ⇒ | If DTC B0081 5A is current, check the SDM for DTC B1001 or a vehicle rollover sensor (ROS) mismatch fault. |
- Verify DTC B0081 4B is not set as current.
| ⇒ | If DTC B0081 4B is current, replace the PPS.. |
- Verify DTC B0081 39 is not set as current.
| ⇒ | If DTC B0081 39 is set as current, replace the PPS. |
- Verify DTC B0081 71 or B0081 0F is not set.
| ⇒ | If DTC B0081 71 or B0081 0F is set, verify the SDM is properly connected and communicating with the PPS. Clear the DTCs. No other repairs are necessary. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
DTC B0081 Two Mode Hybrid
Diagnostic Instructions
DTC Descriptors
DTC B0081 0F: Passenger Presence System Erratic
DTC B0081 3A: Passenger Presence System Incorrect Component Installed
DTC B0081 4B: Passenger Presence System Calibration Not Learned
DTC B0081 5A: Passenger Presence System Plausibility Failure
DTC B0081 39: Passenger Presence System Internal Electronic Failure
DTC B0081 71: Passenger Presence System Invalid Serial Data Received
Circuit/System Description
When the ignition is turned ON, the passenger presence system (PPS) and the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions. When the SDM has completed the power-up mode, the SDM will establish
communication with the PPS. The SDM will also request the instrument panel cluster (IPC) to illuminate both of the PASSENGER AIR BAG ON/OFF indicators ON for 5 seconds. If the SDM determines the correct PPS is installed and functioning normally, the SDM
will illuminate the passenger side airbags ON or OFF based on messages from the PPS. The SDM will also send a message to the IPC to illuminate the appropriate PASSENGER AIR BAG ON/OFF indicator.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
All of the following conditions must exist for 5 seconds:
B0081 0F
The SDM has received a fault present message from the PPS.
B0081 3A
The SDM has received a message from the PPS which indicates a vehicle and PPS mismatch.
B0081 4B
The PPS has failed the rezeroing procedure. Calibration not learned.
B0081 5A
| • | The PPS has lost communications with the SDM. |
| • | When the enabled state between the PPS and the SDM does not match. |
| • | The SDM signal stating the Passenger Status Data Received is not valid within 2.6 seconds after the PPS changes occupant classification. |
B0081 39
The SDM has received a critical malfunction message from the PPS.
B0081 71
The SDM has received invalid or no serial data from the PPS.
Action Taken When the DTC Sets
| • | The PPS will set a DTC, and then communicate with the SDM. |
| • | The SDM disables the Passenger Airbag Module. |
| • | The PPS will illuminate the Passenger Airbag status OFF indicator. |
| • | The SDM requests the instrument panel cluster (IPC) to illuminate the AIRBAG indicator. |
Conditions for Clearing the DTC
| • | The condition for setting the DTC no longer exists and there is no activity on the low speed serial data circuits. |
| • | A history DTC will clear once 250 malfunction-free ignition cycles have occurred. |
Diagnostic Aids
If either the SDM or PPS were replaced, verify that the correct part numbers were used for the vehicle application.
Reference Information
Schematic Reference
SIR Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
SIR System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Important:
| • | When removing connectors inspect for damage, corrosion or poor connection. Damage or corrosion in the following requires repair or replacement of the affected component/connector. |
| • | PPS module harness connector |
| • | SDM wiring harness connector |
- Ignition ON, verify no PPS DTCs are set in the PPS or SDM.
- Verify DTC B1000, B1001, or U0170 is not set as current.
- Verify DTC B0081 3A is not set as current.
| ⇒ | If DTC B0081 3A is set as current, replace the PPS with the correct part number. |
- Verify DTC B0081 5A is not set as current.
| ⇒ | If DTC B0081 5A is current, check the SDM for DTC B1001 or a vehicle rollover sensor (ROS) mismatch fault. |
- Verify DTC B0081 4B is not set as current.
| ⇒ | If DTC B0081 4B is current, replace the PPS.. |
- Verify DTC B0081 39 is not set as current.
| ⇒ | If DTC B0081 39 is set as current, replace the PPS. |
- Verify DTC B0081 71 or B0081 0F is not set.
| ⇒ | If DTC B0081 71 or B0081 0F is set, verify the SDM is properly connected and communicating with the PPS. Clear the DTCs. No other repairs are necessary. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
