GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C1100 00: Base Brake System Pressure Sensor

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Brake Booster Vacuum 5-Volt Reference

C1100 00

C1100 00

C1100 00

--

Signal

C1100 00

C1100 00

C1100 00

--

Low Reference

--

C1100 00

--

--

Circuit/System Description

The electronic brake control module (EBCM) provides a power 5-volt reference to the brake booster vacuum sensor. The brake booster vacuum sensor converts the change in vacuum levels in the brake booster into a voltage signal. This signal is sent to the EBCM. The voltage signal ranges, from 0.13-3.30 volts depending on vacuum levels. The low reference is the return side of the sensor to ground.

Conditions for Running the DTC

    • The ignition is ON.
    • Ignition voltage is greater than 9 volts.

Conditions for Setting the DTC

    • Voltage at the brake booster sensor signal output to the EBCM falls outside the 0.13-3.30 volts range for more than 200 milliseconds.
    • The power 5-volts reference is shorted to ground or battery positive.

Action Taken When the DTC Sets

The red BRAKE Warning indicator turns ON.

Conditions for Clearing the DTC

    • The condition for the DTC is no longer present.
    • The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Reference Information

Schematic Reference

Antilock Brake System Schematics

Connector End View Reference

Antilock Brake System Connector End Views

Description and Operation

ABS Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List for EBCM

Circuit/System Verification

DTC C1100 will set as result of power brake booster vacuum sensor or circuit failure, test for power and ground circuits to the EBCM.

Repair the power or ground circuits.

Circuit/System Testing

  1. Ignition OFF, disconnect the 3 way harness connector at the brake booster vacuum sensor.
  2. Test for less than 1.0 ohm between the low reference circuit terminal 2 and ground.
  3. If greater than 1.0 ohm, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
  4. Ignition ON, test for 4.5-5.3 volts between the 5-volt reference circuit terminal 3 and ground.
  5. If less than 4.5 volts, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the EBCM.
    If greater than 5.3 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the EBCM.
  6. Test for 4.5-5.3 volts between the 5-volt reference circuit terminal 3 and the signal circuit terminal 1.
  7. If less than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
    If greater specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the EBCM.
  8. If all circuits test normal, test or replace the brake booster vacuum sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for EBCM replacement, setup, and programming