GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2007 🢒 Sierra - 2WD 🢒 Steering 🢒 Power Steering 🢒 Power Steering Gear Outlet Pipe/Hose Replacement

Power Steering Gear Outlet Pipe/Hose Replacement Gas Without Hydroboost


Object Number: 1728003 Size: MF

Callout

Component Name

Preliminary Procedure

Remove the engine shield. Refer to Engine Shield Replacement.

1

Power Steering Gear Outlet Hose Clamp

Procedure

Place drain pans under the vehicle as needed.

2

Power Steering Gear Inlet Hose Retaining Plate Bolt

Notice: Refer to Fastener Notice in the Preface section.

Tighten
12 N·m (106 lb in)

3

Power Steering Gear Inlet Hose Retaining Plate

4

Power Steering Gear Outlet Hose

Notice: Refer to Power Steering Hose Disconnected Notice in the Preface section.

Procedure

  1. Disconnect the power steering gear outlet hose from the power steering fluid cooler.
  2. Pull the power steering gear outlet hose out of the steering gear.
  3. Keep all open connections in the power steering system clean and free of debris.
  4. Use the remover/installer J 44586 to replace the steering gear seals if necessary.
  5. Fill and bleed the power steering system. Refer to Power Steering System Bleeding.

Special Tools

J 44586 Power Steering Gear Oil Seal Remover/Installer

Power Steering Gear Outlet Pipe/Hose Replacement Gas With Hydroboost

Removal Procedure
  1. Place drain pans under the vehicle as needed.

    2. Notice: Refer to Power Steering Hose Disconnected Notice in the Preface section.


    Object Number: 1751501 Size: SH
  2. Disconnect the power steering fluid cooler hose clamp and hose (3) from the steering gear (2).
  3. Remove the power steering gear outlet pipe (1) from the steering gear (2).

Installation Procedure

    Object Number: 1751501 Size: SH
  1. Install the power steering gear outlet pipe (1) to the steering gear (2).
  2. Connect the power steering fluid cooler hose (3) and hose clamp to the steering gear (2).
  3. Clean any excess fluid from the vehicle and remove the drain pans.
  4. Fill and bleed the power steering system. Refer to Power Steering System Bleeding

    5. .

Power Steering Gear Outlet Pipe/Hose Replacement Diesel

Removal Procedure
  1. Remove as much power steering fluid from the power steering fluid reservoir as possible.
  2. Place drain pans under the vehicle as needed.

    3. Object Number: 1890205 Size: SH
  3. Compress the power steering gear outlet hose clamp (2).
  4. Disconnect the power steering gear outlet hose (1) from the power steering pump assembly (3).

    5. Object Number: 1890208 Size: SH
  5. Disconnect the power steering gear outlet hose (2) from the steering gear (1).
  6. Remove the power steering gear outlet hose (1) from the vehicle.

Installation Procedure

    Object Number: 1890208 Size: SH
  1. Install the power steering gear outlet hose (1) to the vehicle.
  2. Connect the power steering gear outlet hose (2) to the steering gear (1).

    3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1890205 Size: SH
  3. Compress the power steering gear outlet hose clamp (2).
  4. Connect the power steering gear outlet hose (1) to the power steering pump assembly (3).

    5. Tighten
    Tighten the fitting to 32 N·m (24 lb ft).

  5. Clean any excessive power steering fluid from the vehicle and remove the drain pans.
  6. Fill and bleed the power steering system. Refer to Power Steering System Bleeding.