Pressure control solenoid 1 (PCS1) is used to control on-coming, off-going, and holding pressure in any 1 of 5 clutches. This solenoid is referred to as a pressure proportional to current (PPC) solenoid, since the output hydraulic pressure supplied by this solenoid is proportional to the controlled current command.
The transmission control module (TCM) uses information from the turbine and output speed sensors to detect if a clutch is slipping. The clutch being controlled by PCS1 will vary depending on the shift that was being completed.
DTC P2724 is a type A DTC.
This diagnostic procedure supports the following DTC:
DTC P2724 Pressure Control Solenoid 1 (PCS1) Controlled Clutch Stuck On
• | DTCs P0716, P0717, P0721, P0722, P0875, and P0876 are not active. |
• | The components are powered and ignition voltage is greater than 9.0 volts and less than 18 volts. |
• | Output speed is greater than 200 RPM. |
• | Turbine speed is greater than 200 RPM. |
DTC P2724 sets when the TCM determines the off-going clutch controlled by pressure control solenoid 3 (PCS3) remains engaged during a forward range shift.
• | The TCM illuminates the malfunction indicator lamp (MIL). |
• | When failure occurs in a forward range, the transmission will go to the previous range. If failure occurs in NEUTRAL or REVERSE, the transmission will lock in NEUTRAL while diagnostic response is active. |
• | If the shift selector is moved to NEUTRAL, the transmission will shift to NEUTRAL. |
• | If the shift selector is moved to REVERSE, the transmission will shift to REVERSE or NEUTRAL or in some cases may lock in NEUTRAL. |
• | If the shift selector is returned to a forward range and the transmission is compromised by overspeeding or direction change, the transmission will shift to NEUTRAL. |
• | DTC P2724 is stored in TCM history. |
• | The TCM freezes shift adapts. |
• | The TCM inhibits torque converter clutch (TCC) engagement. |
A scan tool can clear the code from TCM history. The TCM automatically clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without failure.
• | Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions: |
- | A bent terminal |
- | A backed-out terminal |
- | A damaged terminal |
- | Poor terminal tension |
- | A chafed wire |
- | A broken wire inside the insulation |
• | When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change. |
• | You may have to drive the vehicle in order to experience a condition. |
• | This DTC indicates the off-going clutch being controlled by PCS1 is not releasing or is slow to release. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect. |
Important: Clutch failure due to installation of an engine power upgrade is not covered under the manufacturers warranty. |
• | Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur. |
The numbers below refer to the step numbers on the diagnostic table.
This step tests for proper ignition voltage.
This step tests for erratic speed sensor readings.
This step tests for internal hydraulic leakage.
This step tests for clutch capacity.
Step | Action | Value | Yes | No |
---|---|---|---|---|
Schematic Reference: Automatic Transmission Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 | Measure the transmission fluid level. Refer to Transmission Fluid Check . Is the transmission fluid level correct? | -- | Go to Step 3 | Go to Transmission Fluid Check |
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Is the voltage within the specified value? | 9-18 V | Go to Step 4 | Go to DTC P0562 for low voltage or DTC P0563 for high voltage | |
Is speed sensor data erratic? | -- | Go to the appropriate speed sensor DTC | Go to Step 5 | |
Was the line pressure low in a specific range or in ranges where the same clutch was applied? | -- | Go to Step 6 | ||
Notice: Refer to Transmission Stall Test Notice in the Preface section. Conduct a clutch test for all forward ranges. Refer to Clutch Test . Did turbine speed remain at zero in all ranges? | -- | Go to Diagnostic Aids | Go to Step 7 | |
7 |
Are there signs of clutch failure? | -- | Go to Step 8 | Go to Step 9 |
8 | Remove the transmission for overhaul or replacement. Refer to Transmission Replacement . Did you complete the repair or replacement? | -- | Go to Step 11 | -- |
9 | Inspect for a stuck or sticking pressure control valve 1. Refer to Control Valve Body Cleaning and Inspection . Did you find and correct a condition? | -- | Go to Step 11 | Go to Step 10 |
10 | Replace the PCS1. Refer to Control Valve Solenoid Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- |
11 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 12 | Go to Step 2 |
12 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |