GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B1395 03 : Voltage Below Threshold

DTC B1395 07 : Voltage Above Threshold

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

I/P Dimming Voltage Reference

B1395 03 and B3600 03

B1395 03, B2652 00, and B3600 03

B1395 07

B1395 03, B1395 07

Stop Lamp Signal

B1395 03 and B3600 03

--

--

--

Circuit/System Description

Voltage for the interior backlighting components and stop lamp switch activation signal is supplied from the body control module (BCM). The BCM applies a voltage reference through the instrument panel (I/P) dimming voltage reference circuit to the interior lamp dimming switch, which is part of the headlamp switch. When the dimming switch is placed in the desired position, the dimmed voltage setting is applied from the interior lamp dimming switch through the I/P dimming control circuit to the BCM. The BCM then applies the dimmed voltage to the I/P lamps supply voltage circuit and they dim to the correct level.

The stop lamp switch is also supplied voltage on the same circuit for a stop lamp OFF signal to the BCM. When the stop lamp switch is activated the voltage signal circuit to the BCM is opened prompting the BCM to illuminate the stop lamps.

Conditions for Running the DTC

Battery Voltage must be between 9-16 volts.

Conditions for Setting the DTC

B1395 03

The BCM detects a voltage that is lower than 0.33 volt on the I/P dimming voltage reference circuit.

B1395 07

The BCM detects a voltage that is greater than 4.97 volts on I/P dimming voltage reference circuit.

Action Taken When the DTC Sets

    • The I/P dimmer switch will not operate.
    • The I/P dimming lamps will not illuminate.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    •  history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

    •  Interior Lights Dimming Schematics
    •  Exterior Lights Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Interior Lighting Systems Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, cover the ambient light sensor. Vary the interior lamp dimming switch from dim to full bright. The I/P lamps should dim and then become full bright.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the headlamp switch.
  2. Verify that a test lamp illuminates between B+ and the ground circuit terminal 8.
  3. If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify the scan tool Dimming Control Signal parameter is less than 0.1 volts.
  5. If greater than the specified range, test the signal circuit terminal 13 for a short to voltage. If the circuit tests normal, replace the BCM.
  6. Ignition ON, test for B+ between the I/P dimming voltage reference circuit terminal 15 and ground.
  7. If less than the specified value, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  8. Install a 3A fused jumper wire between the signal circuit terminal 13 and the voltage reference circuit terminal 15. Verify the scan tool Dimming Control Signal parameter is greater than 2.6 volts.
  9. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  10. If all circuits test normal, test or replace the headlamp switch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Headlamp Switch Replacement
    •  Control Module References for BCM replacement, setup, and programming