Diagnostic Instructions

DTC Descriptors

DTC P0405 :  Exhaust Gas Recirculation (EGR) Position Sensor Circuit Low Voltage

DTC P0406:  Exhaust Gas Recirculation (EGR) Position Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
EGR 5-Volt Reference Voltage	P0107, P0698, P2564	P0102, P0401, P046C	P0405	P0106, P0699, P2227, P2565	--
EGR Sensor Signal	P0405	P0101, P0405	P0405	P0106, P0401, P0699, P2565	--
EGR Low Reference	--	P0401, P046C	P0406	--	--
EGR MTR High Control	P0403	P0401, P046C	P0403	P046C	--
EGR MTR Low Control	P0403, P046C	P0401, P046C	P0403	P0403	--

Typical Scan Tool Data

EGR Position Sensor

Circuit	Normal Range	Short to Ground	Open	Short to Voltage
Operating Conditions: Engine Running
EGR 5-Volt Reference Voltage	0.98 Volts	0 Volts	0 Volts	1.29 Volts
EGR Sensor Signal	0.98 Volts	0 Volts	0 Volts	4.98 Volts
EGR Low Reference	0.98 Volts	--	4.8 Volts	--
High Motor Control	0.98 Volts	0.98 Volts	0.98 Volts	1.12 Volts
Low Motor Control	0.98 Volts	0.98 Volts	0.98 Volts	0.98 Volts

Circuit/System Description

The engine control module (ECM) uses the exhaust gas recirculation (EGR) position sensor to determine the position of the EGR valve. The ECM sends a reference voltage through the 5-volt reference circuit to the EGR position sensor. The ECM provides a voltage return path for the sensor through the low reference circuit. A variable voltage signal, based on the EGR valve position, is sent from the sensor to the ECM through the EGR position sensor signal circuit. If the ECM detects an EGR position sensor voltage that is less than or more than the normal operating range, DTC P0405 or P0406 sets.

Conditions for Running the DTC

Conditions for Setting the DTC

P0405

The EGR position sensor voltage is less than 0.26 volt for more than 3 seconds.

P0406

The EGR position sensor voltage is more than 4.75 volt for more than 3 seconds.

Action Taken When the DTC Sets

Conditions for Clearing the DTC

DTCs P0405 and P0406 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1. The EGR Position Sensor parameter is between 0.25-4.75 volts.
2. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, test for less than 1 ohm of resistance between the low reference circuit terminal B and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

2. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

3. Ignition ON, and the EGR valve disconnected, observe that the EGR Position parameter on the scan tool is 0 volt.

⇒	If the EGR Position parameter is more than 0 volt, test the signal circuit for a short to voltage. If the circuits test normal, replace the ECM.

4. Ignition ON and the EGR valve disconnected, connect a jumper wire between the 5-volt reference circuit terminal A and the signal circuit terminal C and observe with a scan tool that the EGR sensor parameter displays 4.98-5.02 volts.

⇒	If the EGR Sensor parameter is less than 4.98 volts, test the signal circuit for an open, short to ground, or high resistance. If the circuits test normal, replace the control module.

5. If the circuits, test normal replace the EGR valve motor.

Repair Instructions

Repair Verification

1. Install any components or connectors that have been removed or replaced during diagnosis.
2. Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.
3. Clear the DTCs.
4. Turn OFF the ignition for 90 seconds.
5. Duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.
6. Perform the Diesel Particulate Filter (DPF) Service Regeneration.