GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2000 🢒 Sonoma Pickup - 2WD 🢒 Engine 🢒 Engine Mechanical - 2.2L 🢒 Fuel System Diagnosis

Object Number: 174166 Size: MF
(1)Fuel Pressure Regulator
(2)Fuel Shut Off Adapter J 37287
(3)Fuel Return Line
(4)Quick Connect Adapter
(5)Fuel Pressure Pinch Point
(6)Fuel Pressure Pinch Point
(7)Fuel Pressure Gauge Kit J 29658-D
(8)Fuel Filter
(9)Fuel Pressure Line

Circuit Description

When the ignition switch is turned ON, the powertrain control module (PCM) will turn ON the in-tank fuel pump. The in-tank fuel pump will remain ON as long as the engine is cranking or running and the PCM is receiving reference pulses. If there are no reference pulses, the PCM will turn OFF the in-tank fuel pump after 2 seconds since the ignition switch is turned ON or after 2 seconds once the engine stops running. The in-tank fuel pump is an electric pump within an integral reservoir. The in tank fuel pump supplies fuel through an in-line fuel filter to the fuel rail assembly. The fuel pump is designed to provide fuel at a pressure above the pressure that is needed by the fuel injectors. A fuel pressure regulator, attached to the fuel rail assembly, keeps the fuel available to the fuel injectors at a regulated pressure. The unused fuel is returned to the fuel tank by a separate fuel return pipe.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. When the ignition switch is ON and the fuel pump is running, the fuel pressure indicated by the fuel pressure gauge should be 284-325 kPa (41-47 psi). This pressure is controlled by the amount of pressure the spring inside the fuel pressure regulator can provide.

    2.

  2. A fuel system that drops more than 5 psi in 10 minutes has a leak in one or more of the following areas:

    3. • The fuel pump check valve
    • The fuel pump flex pipe
    • The fuel injectors

  3. Fuel pressure that drops-off during acceleration, cruise or hard cornering may cause a lean condition. A lean condition can cause a loss of power, surging, or misfire. A lean condition can be diagnosed using a scan tool. If an extremely lean condition occurs, the oxygen sensors will stop toggling. The oxygen sensor output voltages will drop below 500 mV. Also, the fuel injector pulse width will increase.

Important: Make sure the fuel system is not operating in the fuel cut-off mode . This can cause false indications by the scan tool.

  1. When the engine is at idle, the manifold pressure is low (high vacuum). This low pressure (high vacuum) is applied to the fuel pressure regulator diaphragm. The low pressure (high vacuum) will offset the pressure being applied to the fuel pressure regulator diaphragm by the spring inside fuel pressure regulator. When this happens, the result is lower fuel pressure. The fuel pressure at idle will vary slightly as the barometric pressure changes, but the fuel pressure at idle should always be less than the fuel pressure noted in step 2 with the engine OFF.

    2.

  2. A rich condition may result from the fuel pressure being above 325 kPa (47 psi). A rich condition may cause a DTC P0132 or a DTC P0172 to set. Driveability conditions associated with rich conditions can include hard starting (followed by black smoke) and a strong sulfur smell in the exhaust.

    3.

  3. This test determines if the high fuel pressure is due to a restricted fuel return pipe or if the high fuel pressure is due to a faulty fuel pressure regulator.

    4.

  4. A lean condition may result from the fuel pressure being below 284  kPa (41 psi). A lean condition may cause a DTC P0131 or a DTC P0171 to set. Driveability conditions associated with lean conditions can include hard starting (when the engine is cold), hesitation, poor driveability, lack of power, surging, and misfiring.

    5.

  5. Restricting the fuel flow causes the fuel pressure to rise above the regulated fuel pressure. Using a scan tool to pressurize the system, the fuel pressure should rise above 325 kPa (47 psi) as the gauge outlet hose is pinched.

    6.

  6. Check the spark plug associated with a particular fuel injector for fouling or saturation in order to determine if that particular fuel injector is leaking.

Step

Action

Values

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Turn OFF the ignition.
  2. Turn OFF the A/C system.
  3. Verify fuel is in the fuel tank.
  4. Relieve the fuel pressure. Refer to the Fuel Pressure Relief .
  5. Install J 29658-D fuel pressure gauge. (7 on illustration).
  6. Turn ON the ignition, with the engine OFF.

    7. Important: To avoid false fuel pressure readings, thoroughly bleed all air out of the fuel pressure gauge.

  7. Bleed the air out of the fuel pressure gauge into an approved gasoline container.
  8. Turn OFF the ignition for 10 seconds.
  9. Turn ON the ignition, with the engine OFF.

    10. Important: The fuel pump will run for approximately 2 seconds. Cycle the ignition as necessary in order to achieve the highest possible fuel pressure.

  10. Observe the fuel pressure indicated by the fuel pressure gauge with the fuel pump running.

Is the fuel pressure within the specified limits?

284-325 kPa (41-47 psi)

Go to Step 3

Go to Step 12

3

Important: The fuel pressure may vary slightly when the fuel pump stops running, the fuel pressure should stabilize and remain constant.

Note the fuel pressure after the fuel pump stops running.

Does the fuel pressure drop more than the specified value in 10 minutes?

34 kPa (5 psi)

Go to Step 10

Go to Step 4

4
  1. Relieve the fuel pressure to the first specified value.
  2. Monitor the fuel pressure.

Does the fuel pressure drop more than the second specified value in 10 minutes?

69 kPa (10 psi) 14 kPa (2 psi)

Go to Step 21

Go to Step 5

5

Is the fuel pressure suspected of dropping off during acceleration, cruise or hard cornering?

--

Go to Step 6

Go to Step 8

6

Visually and physically inspect the following items for a restriction:

    • The in-line fuel filter
    • The fuel feed pipe

Was a restriction found?

--

Go to Step 24

Go to Step 7

7
  1. Remove the modular sender assembly. Refer to Fuel Sender Assembly Replacement .
  2. Visually and physically inspect the following items:
    3. • The fuel pump strainer for a restriction.
    • The fuel pump flex pipe for leaks.
    • Verify the fuel pump is the correct fuel pump for this vehicle.
    • Broken baffles in the fuel tank.
    • The fuel pump electrical wiring for high resistance.

Was a problem found in any of these areas?

--

Go to Step 24

Go to Step 20

8

  1. Start the engine.
  2. Observe the fuel pressure indicated by the fuel pressure gauge.

Is the fuel pressure within the specified limits?

214-303 kPa (31-44 psi)

System OK

Go to Step 9

9
  1. Disconnect the vacuum hose from the fuel pressure regulator.
  2. With the engine idling, apply 41-47 kPa (12-14 in. Hg) of vacuum to the fuel pressure regulator.

Is the fuel pressure within the specified limits and remain constant?

214-303 kPa (31-44 psi)

Go to Step 19

Go to Step 20

10
  1. Turn OFF the ignition.
  2. Relieve the fuel pressure . Refer to Fuel Pressure Relief .
  3. Place the bleed hose of the fuel pressure gauge into an approved gasoline container.
  4. Turn ON the ignition, with the engine OFF.
  5. Bleed the air out of the fuel pressure gauge.
  6. Using a scan tool pressurize the fuel system.

    7. Important: Repeat pressurizing the fuel system with the scan tool as necessary to achieve the highest possible fuel pressure.

  7. Wait for the fuel pressure to build.
  8. Slowly pinch the gauge inlet hose (5 on illustration).

Does the fuel pressure remain constant?

--

Go to Step 21

Go to Step 11

11
  1. Using a scan tool pressurize the fuel system.
  2. Wait for the fuel pressure to build.
  3. Close the valve in the fuel pipe shut-off adapter that is connected to the fuel return pipe (2 on illustration).

Does the fuel pressure indicated by the fuel pressure gauge remain constant?

--

Go to Step 20

Go to Step 22

12

Is the fuel pressure above the specified limit?

325 kPa (47 psi)

Go to Step 13

Go to Step 15

13

  1. Relieve the fuel pressure by placing the bleed hose of the fuel pressure gauge into an approved gasoline container and opening the relief valve.
  2. Disconnect the fuel return hose quick-connect fitting, refer to Metal Collar Quick Connect Fitting Service .
  3. Place the open end of the flexible hose into an approved gasoline container.
  4. Turn OFF the ignition for approximately 10 seconds.
  5. Turn ON the ignition, with the engine OFF.
  6. Observe the fuel pressure gauge with the fuel pump running.

Is the fuel pressure within the specified limits?

284-325 kPa (41-47 psi)

Go to Step 23

Go to Step 14

14

Visually and physically inspect the fuel outlet passages for a restriction.

Was a restriction found?

--

Go to Step 24

Go to Step 20

15

Is the fuel pressure above the specified value?

0 kPa (0 psi)

Go to Step 16

Go to Step 17

16

    Notice: Do not allow the fuel pressure to exceed the specified value because damage to the fuel pressure regulator or the fuel pressure gage may result.

  1. Relieve the fuel pressure by placing the bleed hose of the fuel pressure gauge into an approved gasoline container and opening the relief valve.
  2. Using a scan tool, pressurize the fuel system.
  3. Slowly pinch the fuel pressure gauge outlet hose (6 on illustration) while the fuel pump is running.

Does the fuel pressure indicated by the fuel pressure gauge rise above the first specified value?

325 kPa (47 psi) 414 kPa (60 psi)

Go to Step 20

Go to Step 7

17

Refer to Fuel Pump Electrical Circuit Diagnosis to diagnose the fuel pump electrical circuit.

Was a problem found with the fuel pump electrical circuit?

--

Go to Step 24

Go to Step 18

18

Visually and physically inspect the following items:

    • The in-line fuel filter for obstructions.
    • The fuel feed pipe for a restriction.
    • The fuel pump strainer for obstructions.
    • The fuel pump flex pipe for leaks.

Was a problem found in any of these areas?

--

Go to Step 24

Go to Step 21

19

Locate and repair the loss of vacuum to the fuel pressure regulator.

Did you find and correct the condition?

--

System OK

--

20

Replace the fuel pressure regulator.

Refer to Fuel Pressure Regulator Replacement .

Did you find and correct the condition?

--

System OK

--

21

Replace the modular fuel sender.

Refer to Fuel Sender Assembly Replacement .

Did you find and correct the condition?

--

System OK

--

22

Locate and replace any leaking fuel injectors.

Refer to Fuel Injector Replacement .

Did you find and correct the condition?

--

System OK

--

23

Locate and correct the restriction in the fuel return pipe.

Did you find and correct the condition?

--

System OK

--

24

Repair the problem as necessary.

Did you find and complete the repair?

--

System OK

--